|
|
|||||||
| Register | Options | Profile | Last 1 | 3 | 7 Days | Search | Today's Posts | Mark Forums Read |
 |
|
|
Thread Tools |
|
#91
Fri 08 March 2013, 15:21
|
|||
|
|||
|
But if it was not fun, you would not be doing it. Right?
|
|
#92
Fri 08 March 2013, 17:30
|
|||
|
|||
|
How did you go about the lighting? Individually controlled through a controller but is there a letter cutout and the letter inserted in it and the wiring from the back? Great video
Last edited by pblackburn; Fri 08 March 2013 at 17:33..
|
|
#93
Sat 09 March 2013, 16:25
|
|||
|
|||
|
Hello !
Thank you for sharing your great work ! Could you tell us dimensions of your MechMate ?
|
|
#94
Sun 10 March 2013, 01:26
|
|||
|
|||
|
1500/3200mm working area
|
|
#95
Sun 10 March 2013, 12:56
|
|||
|
|||
|
Its led strip with sticky tape behind so its just cut to segments placed on the back of the letter and then soldered individual segments inside the letter.
|
|
#96
Fri 15 March 2013, 15:17
|
|||
|
|||
|
Danilo,
Sorry for the late reply. Thanks so much for the info. It is always nice to see how people do things.
|
|
#97
Fri 15 March 2013, 15:45
|
|||
|
|||
|
Hello !
Could you tell us which breakout boards did you choose ? Are you satisfied with them ? Hardouin
|
|
#98
Fri 15 March 2013, 15:52
|
|||
|
|||
|
PMDX-126 breakout board with the PDMX-134 motherboard. I have two parallel ports to the board to utilized the full features of the board. It gave me the option of using the PMDX-108 and PMDX-109 later if I wished to. The 126 also allows me to add a 5th drive for my 4th axis. The board has not caused me any problems and I am pleased with it's performance.
|
|
#99
Thu 18 April 2013, 17:52
|
|||
|
|||
|
Very nice job!
|
|
#100
Wed 17 August 2016, 13:41
|
|||
|
|||
|
After one more visit to my friends in Macedonia, these are the new additions
Massive chinese two spindle router (yaskawa servos , 6hp HSD spindles)  Trusty MechMate is still right beside this beast  But improved with CS-Labs ethernet CSMIO IP/S 6 axis motion control and redesigned control cabinet 
|
|
| Register | Options | Profile | Last 1 | 3 | 7 Days | Search | Today's Posts | Mark Forums Read |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| DIY drives from pminmo, Cutting Video, #59 - Bitola, Macedonia | gorantec | MechMates already cutting | 61 | Sat 19 October 2013 03:13 |
| CNC sandline cutting machine | delongcnc | Archives | 7 | Sat 31 October 2009 14:32 |
| Is the MM the right machine for Me? (cutting thin boards and thick foam) | 1foamimprovement | General - MM Build | 5 | Wed 18 February 2009 18:24 |
| Help me to choose a foam cutting CNC machine! | kotys2 | The Market Place | 3 | Wed 03 September 2008 17:33 |
