MechMate CNC Router Forum

MechMate CNC Router Forum (http://www.mechmate.com/forums/index.php)
-   Construction started, but not cutting yet (http://www.mechmate.com/forums/forumdisplay.php?f=77)
-   -   Gantry and Y Car Welded! - Smiths Station, AL (http://www.mechmate.com/forums/showthread.php?t=3730)

1planeguy Fri 03 October 2014 15:03

ok, got a question for the folks that used a external heatsink in their control box. did you sandwich the control box side between the heatsink and the geckos?...or cut out the control box side to allow the heat sink to contact the bottom of the geckos?

pblackburn Fri 03 October 2014 15:06

I cut the box and used thermal transfer paste so the geckos say directly on the heat sink. Sandwich method will kill your thermal transfer.

1planeguy Fri 03 October 2014 15:33

That was my concern...Was thinking thermal tape on both side of the panel side, but the cutout is probably the way to go.

1planeguy Fri 03 October 2014 15:34

And thanks for the quick reply

Duds Fri 03 October 2014 15:50

A steel control box makes an excellent heat sync itself. It has a large mass and surface area.

pblackburn Fri 03 October 2014 16:13

As long as the box is big enough. Yes the box will work. If it is small you can raise the internal temperature up and possibly cause heat issues. Placing the heat outside the box on the fins of the heatsink is preferred.

KenC Sun 05 October 2014 02:40

Not sandwiched. Mount the the heat sink out side and cut the panel so that my driver can tape to the heat-sink directly.

MetalHead Sun 05 October 2014 06:43

Ditto on the cut out.

Look at Gary's box here.

http://www.mechmate.com/forums/showt...8&postcount=76

1planeguy Sun 05 October 2014 17:05

For lack of the willpower to tell the whole sad tale...what is the best place to get the prescribed fuses for the inside of a Gecko 203 drive? Mouser or ???

pblackburn Sun 05 October 2014 19:44

Who ever carries them. You can contact Gecko Drive also. They have great customer support.

1planeguy Sun 05 October 2014 21:30

K, have ordered from MOuser before, they were pretty rough on shipping and handling...was hoping there might be another supplier. Will try Gecko

1planeguy Tue 07 October 2014 09:22

Back at it.
 
Got side tracked for a couple of months with the real job. Blew the dust off the 90% done kitchen table project. Re-discovered the real danger of getting side-tracked from a project like this. You forget where you were at...I started looking for what was still left to be finished and reviewing the wiring diagrams...things just got "fuzzy" after sitting for several months. The net result was sending 48V reverse polarity to the PMDX 134 board with all 4 of my Gecko 203V's attached...promptly zapping their internal fuses. That was the exact moment that I realized spending the little extra money for the 203's was SUCH a good thing, because I would have just turned the cheaper Geckos into paperweights. In this case I made a call to the nice folks at Gecko and ask them how much a set of those little fuses would cost and was informed they "were on the house"...including the shipping. To say Geckodrives has good customer service is the understatement of the year. Those folks are awesome!

A few pictures of the progress made getting the dust blown off the project.

Cutting the side of the box to allow the Geckos to make direct contact to the heat sink...
http://www.kilocharlie.us/MechMate/pictures/31sm.jpg

Attaching the heat sinks with a couple of bolts and a few blind rivets.
http://www.kilocharlie.us/MechMate/pictures/32sm.jpg

Mounted the Geckos to the heat sink with a thermal pad. All was going well...right up until I zapped the fuses in the drivers :-(
http://www.kilocharlie.us/MechMate/pictures/33sm.jpg

In other progress, got Mach3 installed on a laptop, IP address configured and talking to the ethernet smoothstepper. Need to verify it is talking to the PMDX 126. Not sure yet if Mach is seeing both of the emulated LPT ports that the ESS provides. Want to hook up a quickie test circuit to emulate a Z-zero touch probe and verify that Mach can see it.

Onward...

smreish Tue 07 October 2014 09:51

...Gecko has always been awesome with Customer service. Glad you had a good experience too.

KenC Wed 08 October 2014 02:02

Nicely done!
Other then lowering the box temperature & cool looking box. The added bonus of a external heat sink is that you free up lots of premium box space instantly. Easier to for organizing your wiring & more room for more bells & whistle.

1planeguy Mon 13 October 2014 08:52

Ken, I thought for a while about sticking the computer in the box as well...plenty of room. Could have mounted the motherboard and everything on the door and made it nice and clean. Theeeeeeennnnnn I went in to a Best Buy and saw how cheap touch screen laptops are getting. I decided the box mounted PC would actually have more cables (keyboard, mouse, monitor) running between the workstation and the box then a laptop setup with a ESS (ethernet cable) So I am setting it up with an old laptop and one day I will switch it out to a touch screen laptop to run MACH 3 to give touch screen control of MACH 3.

1planeguy Mon 13 October 2014 09:37

Well...it is a good thing to have this forum. Without this I would have no one to hear the "WOO HOO's" when I figure something out ;-) Family doesn't exactly "get" the whole CNC build in the garage thing and certainly don't understand the satisfaction of figuring out something that has had you beating your head on the wall for a few hours. Let's just say that MACH 3 is in control of the kitchen table project and things MOVE! Got all motors jogging and MACH 3 controlling the spindle relay. Still need to setup a Z-Zero touch plate circuit. intending to go ahead and install 2010 screenset and figure out the particulars there.

Waiting on about 2 tons of steel to get fab'ed for a bolt together Mechmate table and a hydraulic rubber pad press setup for a related but separate project. The shop is about to get BUSY...

Kitchen Table project- MACH 3 in control

Fox Mon 13 October 2014 11:26

I am still waiting for the first one to dress up his steppers like penquins and add some flappy feet the to the axles, when I see those laying next to each other on a test bench :D

Congrats ! Feel nice, heh !?

KenC Tue 14 October 2014 00:57

Separating the PC from control panel is a very wise decision, the control panel space vanishes in a hurry when you put the Mobo in... & the wires for keyboard & other mod-cons....

1planeguy Mon 20 October 2014 09:13

Got to give a pat on the back to fellow MechMate builder "Drexel" on the forum... finished taping his gear rack and realized he had at least another machine worth of 3M tape left...passed his extra down the line to me. Still some generous folks out there in the world...good to meet another one!

Thanks again!

Rusty Nuts Tue 21 October 2014 19:07

Hi 1planeguy

Great looking build. Getting the motors turning is great progress, won't be long now till your making chips. Where is Smiths Station?
I'll be watching from Valley Grande.

Gary

1planeguy Fri 07 November 2014 19:30

Well, the project just got a lot heavier! Had a shop I do work for run the material through their CNC beam line. Everything is pre-punched and cut to length...now time to fire up the welder and stick metal together!
http://www.kilocharlie.us/mechmate/pictures/34sm.jpg
http://www.kilocharlie.us/mechmate/pictures/35sm.jpg
http://www.kilocharlie.us/mechmate/pictures/36sm.jpghttp://www.kilocharlie.us/mechmate/pictures/37sm.jpg

Fox Sat 08 November 2014 03:42

Dang, everytime you think you've seen it all... Pre punched cnc cut beams, that's like triple word value in the diy cnc builder world. I thought I was being fancy when I welded mine one a big welding table at my friends shop. ;)

rcboats1 Sat 08 November 2014 11:49

That's cheating, (I wish I had thought of that).

Tom Ayres Sat 08 November 2014 14:04

Its not really cheating if you can afford it or you have friends in the right places.;)

Alan_c Sat 08 November 2014 15:18

I still think its cheating (only because I can't afford it and my friends are definitely not in the right places :D )

servant74 Sat 08 November 2014 17:26

Yep. Cheating is a relative term. It is only cheating because I don't have friendly local vendors and friends with the capabilities either!

It is good to see that someone else thinks out of the box and uses the tools and facilities available to them! Yep, I am jealous because I can't find a way to cheat like that too!

Way to go 1planeguy!

Tom Ayres Sun 09 November 2014 05:18

Alan, look at it this way he doesn't get to experience all of the build like the rest of us.

Alan_c Sun 09 November 2014 05:50

LOL Tom, so what you are saying is we need to feel sorry for 1planeguy? :rolleyes: :D

Tom Ayres Sun 09 November 2014 07:09

Exactly what I said:D

1planeguy Sun 09 November 2014 09:19

I'll even admit this is cheating ;-) If you saw the accuracy this stuff is cut to...Y'all would probably throw me off the Mechmate builders site. There are actually 2 projects on that trailer...a 50 ton shop press for doing rubber pad forming and the 5'x12' mechmate. I'm actually welding up the press first. The I-beams are cut within 1/32 of intended length and dead square. I saw a demonstration of the CNC saw that did a squaring cut and then moved the beam down and cut a perfect 1/8 slice off the end (of a 21" tall beam)...it makes trying to make things square a heck of alot easier for sure.

pblackburn Sun 09 November 2014 09:26

I can't say anything other than great idea. I did most of my build using various equipment I had access to (cnc and manual mills and lathes, heat treat processes, etc). That kept the cost down and improved the quality of the build. I would not say it is cheating but rather an appropriate use of resources.

1planeguy Wed 07 January 2015 08:03

Still here...
 
Got the steel for the Mechmate and one other project a while back. For a couple of reasons the "other" project actually took priority over the Mechmate, so I've been working on it and storing the Mechmate material. Thought some folks might be interested in the "other" project. (Have seen a few builders that were using their Mechmate to make aircraft parts) This is a rubber pad forming press. I put a few pictures in a Flickr album...several in progress photos and a computer rendering of the final result. Waiting on a shipment of high strength bolts then paint and set the bed in place on the hydraulic rams. Gonna be interesting !

https://www.flickr.com/photos/128567...7647813898144/

IMMark Thu 08 January 2015 06:52

Wow, looks awesome. I have seen, a much smaller scale version, and was impressed with the results. Please keep posting progress, would love to see that working.
Thanks
Mark

1planeguy Sun 22 February 2015 09:47

Big parts coming together
 
Finally got the other project out of the way and got started assembling the MechMate "kit" I had cut and punched earlier. After a couple hours of work, I got the baseplates and capplates for the posts welded on and temporarily bolted together. Starting to come together...
http://www.kilocharlie.us/mechmate/pictures/39sm.jpeg

http://www.kilocharlie.us/mechmate/pictures/38sm.jpeg

http://www.kilocharlie.us/mechmate/pictures/40sm.jpeg

http://www.kilocharlie.us/mechmate/pictures/41sm.jpeg

http://www.kilocharlie.us/mechmate/pictures/42sm.jpeg

http://www.kilocharlie.us/mechmate/pictures/43sm.jpeg

Fox Sun 22 February 2015 11:37

Interesting approach, are you going to do something similair to the sides with braces tot avoid racking?

1planeguy Sun 22 February 2015 14:34

End to end the thing is already rock solid. Have diagonal tube braces to weld between the legs and the ends of the main beams with a cap plate to maintain the ability to break it down. The side to side direction is my only concern with the bolted connection between the legs and the cross channel. With the movement against a shear connection like that, it will be tough not to get some wiggle there. Am considering laying a bead of weld across the top and bottom of that joint knowing if it ever does need to come apart it will just be a quick cut with the side cutter to break it down.

Robert M Mon 23 February 2015 12:24

Quote:
Originally Posted by Fox View Post
Interesting approach
I'll second that :rolleyes:
Looking forward seeing the advancement !
All the best

1planeguy Tue 03 March 2015 16:18

Test fit
 
Test fit the long angles to the main beams...surprise surprise...all the CNC punched holes lined up. Getting ready to cut them down to height and start the grinding. Got the diagonal braces welded in...they have a plate at the top to allow it to be broke down if the need ever arises.http://www.kilocharlie.us/mechmate/pictures/44sm.jpeg
http://www.kilocharlie.us/mechmate/pictures/45sm.jpeg

HomeMadeCnc Mon 16 March 2015 17:19

Thats one beefy build!
Looking real good
Cheers
Tim

1planeguy Fri 20 March 2015 09:40

Okay all you guys that have wired the Huanyang inverter. Am having a brainless moment and don't want to let the smoke out of the thing. When you wire a standard 220V-single phase in the U.S. you have 2 "hot" leads of 110v apiece (typically colored red and black) then a common or neutral (white) and then the ground (green)...well everything I've read says that to wire it 220V single phase I use the R,S and E terminals...from what I see on youtube videos and I few sources from varies companies that import them is black to R, white to S and green to E. Well that is missing a whole 110v leg? It isn't 220V?! I'm lost and am not afraid to admit it...I would be ashamed to admit I smoked the thing because I was afraid to say I was lost...but I digress...
Picture to follow...

http://www.kilocharlie.us/Mechmate/p...20question.jpg


All times are GMT -6. The time now is 06:49.

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.