PM Sent

I will be ready to buy very shortly and i am still interested in those motors waiting for a pay check and a car to sell. Please send me an invoice for BC01 for Bisbee Arizona 85601 I am ready to purchase that part of the kit now

Hi Mike,

Any luck with pricing on power supplies and motors yet? I'm going to spend the money either way, I might as well support you if I can get what I need.

I sent you a PM .

Cables
 

Ok everyone. I need to get some feedback on cables. I am about to order rolls of the F-CY-JZ in

20 Gauge

2 Core - Pricing now
4 Core - Price will be .88 per foot
8 Core - Price will be 1.32 per foot

I know from research we should be fine with the 20 guage wire.

What you will get will be a total length of your desired wire core count. NO CUT CHARGE.

Shipping will be about $25.00 for what ever amount you order.

I just want to find out who is interested in cable so I can get this piece moving.

Mike,

Count me in for the total quantity that will be needed ( 4' x 12' table ) for my build. As for the exact amount, when the time comes, I will need your help in trying toi figure it out.

Robert

Quick rough sketch of wire length required:

GL = Gantry Length; TL = Table Length; DCB = Distance to Control Box; WL = Working Length for strain relief, stripping, connections.

From Y-Car, or Gantry Far: GL + TL + DCB + WL + WL
From Gantry Near: TL + DCB + WL + WL
From Y-Car to Gantry Far: GL + WL + WL

For a 60" x 120" (4'x8' working area) table with 24" (2') allowances for connections and a wall mounted box needing 72" (6') to reach:

(3) 4-core for motors at 5'+10'+6'+2'+2' = 25' * 3 = 75'
(1) 4-core for motor at 10' + 6' + 2' + 2' = 20'
(1 ea) 8-core for low voltage sensors and controls, 2-core estop at 5' + 2' + 2' = 9'
(1 ea) 8-core for low voltage sensors and controls, 2-core estop at 10' + 6' + 2' + 2' = 20'

So 95' of 4 core, and 29' each of 8 core and 2 core. For the 4' x 12', 111' of 4 core, 34' each of 8 core and 2 core.

Don't forget the 25' (or 29') of spindle or router feed (for a router, that's a standard extension cord).

Mike,
Count me in for
120 ft 4 core
50 ft 2 core
50ft 8 core
And thanks

I got a PM recommending that I add the option for the remotes to the list of items I have available. So here is what I have. This set will be called RB01 and will be two sets like the ones pictured for $135.00 delivered in the lower 48 States.

RB01 Contains the following items.

2 - Pushbutton Enclosure, 3 hole, Extinguishing Thermoplastic
2 - Legend Plate, RED, Emergency Stop
2 - Legend Plate, Black, Start
2 - Legend Plate, Red, Stop
2 - Flush Operator, Yellow (For soft stop using BOB E-stop)(Really a PAUSE Button)
2 - Flush Operator, Green
2 - Emergency Stop pushbutton Non-metallic, Twist-to-release, Red, (Wired to Contactor in control box to shut down power to system)
2 - Single Contact Block, 1 N.O.
4 - Single Contact Block, 1 N.C.

If your looking for Electic Parts, review this thread and shoot me a PM. I have Motors, PS , Basic Electric Kits, Remotes, PMDX and Driver boards.

The BC01,GB01,RB01 is $1249.12 delivered in the lower 48 states.

MC01 - 4-640 oz Motors and 1 Matched power supply $595.00 delivered in the lower 48 states.


I also have a PMDX-122 and 4 Gecko 202 drivers I will sell for $475.00 delivered in the lower 48 states.

I also have at least 4 OM7.2 Motors that I will sell for $850.00

I have have a lot of stuff in stock, Including laser cut and bent parts.

Mike,

Any plans to carry the standard IGUS cable carrier. I've reviewed several threads but so far have not found part # for what everyone is using. The other thing I have not found a source for is the gas shock, but that's not electrical.

McMaster Carr is a good source for both

Reid Supply also has the igus carrier or igus.com will sell you it from the online store.

Sean

Mike
Is this cable still available, or is there a newer better product available? What connectors are being used to connect the stepper motors back to the control box?

I have plenty in stock. This is good motion wire. Most have opted to omit connectors and wire from the motors all the way into the box through grommets to terminal blocks. Fewer fail points. The BC01 kit I also have in stock has a lot of the basics needed including a 20x20x10 NEMA 4/12 box.

Mike, I have already purchased the BC01 kit and 4 640oz NEMA 34 motors and 1 matched power supply from CV Supply great people to do business with. Talk to Mike (ha! ha!). What is the cost per foot of the 8 wire cable. How much is generally needed? Any other cable needed.

Ha !!! Guess I should check my records before responding :) !!! Wire is a kit. 82 feet of 8 core and 164 feet of 4 core. I just got two spools and need to check and make sure the price per sqft foot is going to hold as before. I'll PM you with an update tomorrow.

per SQ/FT !!!? that is a lot of wire....:)

Oops that would be a lot of wire !!! Thx !

Metal please send me a invoice for the gb01 please

Not sure what a gbo1 is
 

Are you sending this to the correct person

Mike, please contact me about a wire order, thanks.

Mike not Mike
 

are you looking for metalhead not hursh

I'm sorry for the confusion Hurshy, I am talking to Metalhead Mike.:)

Are there any updates to the offerings? All things (close to) equal, I'd rather support Mike, and maybe save myself some shopping headache.

This kit is still basically the same. A few changes have been made, but not many. My kits do save you a good bit of time for sure.

I have aditional parts as well and I can PM you a list.

hello, buy some things mike and recommend