MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance Troubleshooting

User Name Remember Me? Password

Page 3 of 3 < 1 2 3

Threads in Forum : Troubleshooting

Forum Tools

Search this Forum

		Rating Thread / Thread Starter	Last Post	Replies	Views
		Moves at different speeds for different directions - feed rates incorrectly defined Kobus_Joubert	Sun 22 March 2009 05:16 by Gerald D	16	26,665
		Cannot get good jog speeds - first thought PS voltage too low, then current error kwang90020	Tue 17 March 2009 13:28 by Gerald D	11	21,352
		Loosing steps - noise interference problems MariusL	Sun 15 March 2009 05:34 by MariusL	14	25,836
		One stepper motor does not change direction - drive needs reset waynec	Mon 16 February 2009 09:22 by waynec	13	24,579
		Circles are not cut round - loose pinion gears sailfl	Sun 15 February 2009 17:19 by bradyaero	21	34,369
		Lurching at Reset - interference from spindle VFD waynec	Thu 05 February 2009 17:00 by bradm	12	25,092
		Shudder along X Axis - unresolved ( 1 2) sailfl	Sun 28 December 2008 14:32 by sailfl	30	43,292
		Toggling inputs - faulty Campbell BoB Alan_c	Mon 08 December 2008 10:30 by Alan_c	15	29,526
		One axis looses steps when going fast under load - change accel setting Greg J	Sun 07 December 2008 21:55 by Gerald D	10	19,445
		Steps getting lost - poor quality parallel port cable javeria	Wed 03 December 2008 06:35 by javeria	5	12,045
		One of the four motors not running properly - faulty Geckodrive 203V cncb	Sat 08 November 2008 07:46 by cncb	8	21,942
		Problems with cooling fan.. - impeller touched the mounting plate cncb	Tue 04 November 2008 04:47 by cncb	17	19,939
		Motors won't turn after the setting up - PMDX-122 jumpers incorrect lunaj76	Fri 31 October 2008 04:20 by J.R. Hatcher	13	18,457
		Some files don't cut smoothly - Mach's interpret. of G-Code from various CAM programs ( 1 2) Greg J	Sat 25 October 2008 14:52 by Gerald D	30	40,494
		Runs out of steam? Machine freezes during cutting - controlling PC's performance liaoh75	Thu 23 October 2008 22:34 by liaoh75	11	36,927
		Cannot get motor to turn - Mach Ports & Pins setup kalimero	Tue 06 May 2008 09:50 by Greg J	18	41,494
		Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault ( 1 2) Daya	Mon 21 April 2008 01:05 by Glenn D	45	95,365
		Machine cuts out after cutting for a while - Loose wire on E-stop circuit Hugo Carradini	Mon 31 March 2008 12:18 by Hugo Carradini	8	19,643
		Getting comms between PC and PMDX-122 - Finding the correct port address ekdenton	Wed 26 March 2008 11:14 by ekdenton	2	10,699
		One motor goes wrong way - How to reverse its direction grandpi	Sun 17 February 2008 22:03 by Gerald D	2	13,490
		Machine locks up while travelling at high speed - Tuning the motor speeds and accels Doug_Ford	Sun 03 February 2008 21:55 by Gerald D	3	14,447
		Glitches in cut paths (rounded corners) - Using the Constant Velocity mode of Mach J.R. Hatcher	Mon 28 January 2008 05:22 by J.R. Hatcher	3	10,978
		System stops, as if the E-stop has been pushed? - Change De-Bounce setting in Mach Gerald D	Thu 24 January 2008 17:51 by smreish	4	11,196
		No 5V supply out of PC - Polarity reversed J.R. Hatcher	Thu 24 January 2008 16:50 by J.R. Hatcher	1	8,169
		Contactor does nothing when powered? - Correct terminals for coil Doug_Ford	Sun 11 November 2007 18:23 by Doug_Ford	11	25,142
		Upgraded Mach, now the motors won't turn - Different ports/pins for later Mach Hugo Carradini	Thu 25 October 2007 11:45 by Hugo Carradini	19	33,717
		Machine runs far too slow (or fast) and the wrong distances - Confusing inch/mm 's Hugo Carradini	Tue 25 September 2007 09:44 by Hugo Carradini	2	14,931
		Jerky movement of the gantries - Limit Overides activated in Mach ( 1 2) fabrica	Tue 23 January 2007 09:39 by fabrica	31	40,356
		Motors do not move after initial setting up - Mach setups fabrica	Fri 19 January 2007 01:04 by fabrica	17	17,752

Page 3 of 3 < 1 2 3

Display Options

Showing threads 81 to 109 of 109

Sorted By Thread Title Last Post Time Thread Start Time Number of Replies Number of Views Thread Starter Thread Rating Sort Order Ascending Descending From The Last Day Last 2 Days Last Week Last 10 Days Last 2 Weeks Last Month Last 45 Days Last 2 Months Last 75 Days Last 100 Days Last Year Beginning

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General - MM Build About this Forum The Market Place Personal Build Histories     Introduce yourself and start planning     Construction started, but not cutting yet     MechMates already cutting Structure & Mechanics     10. Base Table     20. Gantry     30. Y-Car     40. Z-Slide     50. Toolheads     55. Dust Management Common Assemblies & Parts     Profiled (laser cut) & bent steel plate     Motors & their mountings     Rails & Rollers     Driving Mechanisms: Rack/pinion, gears, screws, belts & chains Electrical & Electronic     60. Wiring & Cable Management     70. Control Systems     701. Motor Drives     702. Power Supplies Computing, Software & Programming     80. Computer Hardware & Software     Graphics & CAD     CAM     CNC motion control software     Utility software After Building the Beast - Operating , Troubleshooting and Maintenance     General - MM Operating     Cutting various materials - bit selection, feeds, speeds     Troubleshooting     Maintenance     The Show Room Miscellaneous hardware and software     Human Interface Devices (HID's)     Miscellaneous / General / Whatever / Catchall     Golden Resources     Test Area for this forum     Downloads Dxf Library Archives