#1
|
|||
|
|||
Cut list ...
I am trying really hard to compose a cut list
do I understand the follow below correctly ? thanks in advance Jason |
#2
|
|||
|
|||
I found the answer ... thanks
|
#3
|
|||
|
|||
Where did you find the answer?
|
#4
|
|||
|
|||
well ..
your right i didnt find it
i just did more reading and grew more confident with my answers and couldnt delete my post i couldnt find 3-4 , i was pretty sure about the rest you would tell me if they were wrong ? jason |
#5
|
|||
|
|||
That all looks correct; in the picture, #1 and #2 also have 1010324 on their ends and
#21-#24 have 1010334 on their ends. Note that there aren't just two of #3/#4 1010302 - those are the two end bearers out of the set of cross bearers shown on 1010300; often there are 8 for standard size sheet goods, but it depends on the table length. |
#6
|
|||
|
|||
Quote:
i couldnt figure out if there was 3 and 4 and then 8 more 1010302 yes i see the end caps and wont forget them thank you again |
#7
|
|||
|
|||
start building and if there is something missing you know that you missed something don`t forget the decals at the end most oaks leave it till the end and then it is a race to get that number.Get the logo first !!! Bet you will have something standing in your shop soon to stick it on.
|
#8
|
|||
|
|||
hmmm ...
Its true , I havent completed a mechmate , or even started on one ...
I have come to understand , the mechmate in the plans might not be for me ... as you guys already knew ... as it rather large and industrious ... however I have completed over 20 classes in my quest to complete a CnC table ... I have thought myself Vcarve and much trial and effort was able to this create file ... then I was able to cut this ... and create this ... Yesterday , I almost completed this .. just waiting on the tmolding ... before I install today I am starting on my 3rd project ... something like a single unit one these .. http://photos.mlive.com/detroit/2011...room_to_4.html I am currently having to much fun to build a mechmate or something like it , but I will be back ... Jason Last edited by Gerald D; Fri 06 April 2012 at 07:04.. |
#9
|
|||
|
|||
Is your "tiger" stuff a laser engraving ?
If yes, what is the power of your laser and advance settings ? Last edited by Gerald D; Fri 06 April 2012 at 07:03.. |
#10
|
|||
|
|||
No worries ..
Yes my Tiger stuff is laser engraved ... and I cant recall the settings off the top of my head ... I know it took several passes on both vector and raster mode ... before I was happy .. I can look them up for you later today ...
Here is a sign I am currently creating for the CnC with the different tool paths I am learning ... might cut it soon ... hope you liked my work ... Jason Last edited by Gerald D; Fri 06 April 2012 at 07:03.. |
#11
|
|||
|
|||
A spammer left a message here earlier and this set off some misunderstanding between 2 members. I have deleted the major repercussions.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Build list? | customcarves | General - MM Build | 8 | Thu 15 December 2011 10:45 |
need someone to check my list | thereclinerman | 702. Power Supplies | 8 | Tue 17 November 2009 18:49 |
Missouri looking to add to list | mohobbygo | Introduce yourself and start planning | 2 | Fri 24 April 2009 22:19 |
Looking for material list | extremecanvas | General - MM Build | 4 | Wed 25 March 2009 23:37 |
Making a wish list | Medemt | 70. Control Systems | 1 | Wed 25 March 2009 18:22 |