Laser Cut and Bent Parts - United States - Page 5

narso · #**121** Mon 19 October 2009, 18:17

This is my Zip Code in USA
TX 75065

jbmclain · #**122** Mon 19 October 2009, 21:01

Ned, I just sent you a PM.

Only three sets left.

darren salyer · #**123** Thu 22 October 2009, 12:46

Been lurking too long. Shipping to 63385?

jbmclain · #**124** Thu 22 October 2009, 19:44

Darren, I just sent you a PM.

Joe

Hillbillie · #**125** Fri 23 October 2009, 21:07

Joe,

How often do you make these sets? I dont need one now but in about 3 months I will.

Larry

jbmclain · #**126** Sun 25 October 2009, 07:09

Larry, sad to say that I will have sold my last set in a few days.
The person that I was dealing with to cut the parts was laid off due to the economy. I don't think the new guy is going to give me the same rate to cut and bend a set of parts. But I guess I could see.
If I'm not mistaken. Castone is still selling laser cut parts.

Joe

davida1234 · #**127** Sun 25 October 2009, 18:19

Hi Joe,

Do you have any sets left? Zip code 92651

david@aa-group.com

davida1234 · #**128** Sun 25 October 2009, 18:19

And if you do, how do I pay?

Gerald D · #**129** Mon 26 October 2009, 09:39

Quote:

Originally Posted by jbmclain

Larry, sad to say that I will have sold my last set in a few days.
The person that I was dealing with to cut the parts was laid off due to the economy. I don't think the new guy is going to give me the same rate to cut and bend a set of parts. But I guess I could see.
If I'm not mistaken. Castone is still selling laser cut parts.

Joe

Castone is in this thread: Laser cut and formed parts - Tennessee

jbmclain · #**130** Tue 03 November 2009, 20:09

Alabama isn't dead yet.

Metalhead and I are working together to see if we can keep the parts flowing here in the US. We will be meeting with the local Laser/Fabricator guys hear this week to see if we can keep the set available at a affordable price.

We will let you know what we find out.

Joe

Gerald D · #**131** Tue 03 November 2009, 22:28

Good to hear that there is still life in Alabama! You served this community very well in the past.

GregZ · #**132** Thu 05 November 2009, 01:32

I -just- got a kit from Joe that it turns out I am not going to use (I found an already-built machine for a great price).

The box is unopened.

I'm in Portland, OR

I'd like to get what it cost me, of course.

Anyone interested?

Greg

MetalHead · #**133** Thu 05 November 2009, 05:32

I talked with Joe and the Laser Parts company yesterday. I should have what I need in the next day or so to get a kit pulled together for sale. Just PM me if you are interested in a set of parts and when I get them pulled together I will let everyone know.

MetalHead · #**134** Tue 24 November 2009, 14:38

Update on Laser Parts.

I had a test set ran to make sure the new folks met spec. I will touch the parts tomorrow to make sure they are good then I will order some sets.

daoneua · #**135** Mon 30 November 2009, 20:11

Greg do you still have a kit from Joe? that you want to sell.

GregZ · #**136** Mon 30 November 2009, 22:07

I do indeed!

MetalHead · #**137** Wed 16 December 2009, 21:07

Completed some parts for one of the members .

1x M1 30 224 Idler stub shaft.
6x M1 20 220 Bearing support base.

PM me if you need a set. I have more.

I am still tracking on the Laser Parts and they should start being ready soon !!

slackkeymike · #**138** Wed 23 December 2009, 14:21

I am confused (and new) here. When someone supplies laser cut kits, what exactly is in the kit?

Thanks!

Mike (also in Alabama)

riesvantwisk · #**139** Wed 23 December 2009, 18:48

S.Mike,

usually they are the parts found in ProfilesBends30Jun08.zip (see downloads )

However some people help others out with additional parts when they cannot do the work because the don't have the machines to make them, the above could be such a case when somebody doesn't have a lathe to make the Bearing support base.

Ries

MetalHead · #**140** Thu 24 December 2009, 19:07

Here are some cool shots from a set of parts I made today (PM if you need a set) I am already checking a few long distant orders for folks.

I like the action shot of the Lathe boring the bushings.

I did figure out the the next set will have the idler on the outside end and I will give a little more stock between the bushings. This lets me cut off the Idler then drill the holes and finish size the bushings on the blank.

I can then go over and cut them off with the metal band saw. My parting skills in need of some work

. !!!

MetalHead · #**141** Thu 24 December 2009, 19:17

Here are the parts test fitted. The idler is snug and will be pressed into the point it is flush with the outside of the idler shaft. I have to resist pressing the bearing on.... I won't say how I know they are hard to get back off

!!!

bolingerbe · #**142** Thu 24 December 2009, 20:07

S.Mike,

Ries was correct, I did not have a lathe and MetalHead(Mike) assisted me with this at a very good price and well machined parts. I purchased my Laser Cut Parts from Joe "Sweet Home Alabama" and was very pleased with the quality and price. I could not have built this without the technical help and assistance that this forum has. A lot of the builders on this site have the equipment needed to do most of the work, but it is geat when the same ones step up and help others.

Johannescnc · #**143** Sat 26 December 2009, 04:46

Great pics Mike! and also inspiring... I want a lathe!!!

slackkeymike · #**144** Sun 27 December 2009, 11:23

Can someone point me to projects where the bed size was scaled down? I do not need (or have room) for 4x8. I am (hopefully) assuming that the gantry can remained unscaled (if width is mainained).

Mike

tufanca · #**145** Sun 27 December 2009, 16:08

MechMate yeni versiyon cnc router çizimi yokmu? 2009-2010 çizimi bekliyoruz

swordfish1382 · #**146** Tue 19 January 2010, 00:47

Sir I am located at 36362 FORT RUCKER AL any sets left? Thank you for your time ERIC

MetalHead · #**147** Tue 19 January 2010, 01:47

Sent you a PM - More sets will be ready in a few days.

isladelobos · #**148** Tue 19 January 2010, 07:10

Hey Mike.
You forget me!!!!

MetalHead · #**149** Tue 19 January 2010, 07:27

No I haven't - Just trying to get time to figure out the customs forms. I will try to get through them this week.

Pauld · #**150** Wed 20 January 2010, 13:10

I am new to the forum and was interested in what the cost is for a set of the laser cut parts and what would shipping be to a 24153 zip code.

Just want to say i have looked over the site for some time now and i am amazed at all the info that is available here. By the way has anyone done a video of the assy. of the mechmate and is it available.
Paul

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Laser Cut and Bent Parts - Europe	milkov	Profiled (laser cut) & bent steel plate	33	Fri 17 August 2012 13:13
Laser Cut and Bent Parts - India	dsingh82	The Market Place	10	Thu 01 October 2009 04:14
Laser cut and formed parts	Castone	Profiled (laser cut) & bent steel plate	5	Sat 05 September 2009 00:40
Greetings all From United States	derekkest	Introduce yourself and start planning	3	Tue 09 June 2009 06:29
laser burnt pre-bent parts	ghostlx	Archives	4	Mon 22 September 2008 05:18