MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Personal Build Histories > Construction started, but not cutting yet
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #1  
Old Fri 21 April 2017, 08:52
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
Working on Rack and Motors - Ball Ground, GA

I started this in the intro thread and moved it here to ask questions. Its just a little different than the MM design as far as the table goes. I am going to build a bigger table later for it. I need to be able to move this one when needed.
So my goal is to get one working and move it to a full size later.
Attached Images
File Type: jpg mymech1s.jpg (70.9 KB, 214 views)
Reply With Quote
  #2  
Old Fri 21 April 2017, 08:54
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
My first question. Is 1/4' x 4" x 18" gauge plate the best size for the z axis? I see longer one mentioned on here, and some of the drawings show different size lengths for different options.
Reply With Quote
  #3  
Old Sat 22 April 2017, 04:21
MetalHead
Just call me: Mike
 
Columbiana AL
United States of America
It really depends on what your doing. If your going to do typical stuff on the machine the 18 inch is fine. I just built this one for a member and it has the 18 inch plate.
Attached Images
File Type: jpg Z Slide 1.jpg (143.9 KB, 210 views)
File Type: jpg Z Slide 2.jpg (56.9 KB, 209 views)
Reply With Quote
  #4  
Old Sat 22 April 2017, 07:28
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
Thank you. That looks great. I just wanted to make sure I was utilizing the entire 8 inches.
(**FYI. All the bent parts I bought from you fit perfectly.)
Reply With Quote
  #5  
Old Sun 23 April 2017, 21:18
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
I ordered this. Made in USA - 18 x 4 x 1/4 Inch, AISI Type O1, Tool Steel Oil Hardening Flat Stock from
www.mscdirect.com
Reply With Quote
  #6  
Old Mon 24 April 2017, 05:44
MetalHead
Just call me: Mike
 
Columbiana AL
United States of America
I have this assembly now available as a part ZS01 for $625.00 delivered if anyone is in need of the part. V rails are milled and not ground. I have built jigs to allow complete milling of this 18 inch and 20 inch plate.
Reply With Quote
  #7  
Old Wed 26 April 2017, 16:09
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
Z Axis Slide Plate

First piece ordered arrived.
Now on to figure out the slider plate.

I think it is 1" x 3" x 1/4" x 28" long and then cut back to 26 (+/-) inches after fitting spring. Is that correct?
Attached Images
File Type: jpg 18 inch steel plate.jpg (17.4 KB, 146 views)
Reply With Quote
  #8  
Old Thu 27 April 2017, 13:57
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
What is the best way to mill or ground the Z axis

I am a little confused on the Z axis slide plate grinding. Is it best to take it to a machine shop and have it milled?
Reply With Quote
  #9  
Old Thu 27 April 2017, 16:14
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
Belay My Last. Figured it out...To simple.. Returning to course.
Reply With Quote
  #10  
Old Fri 28 April 2017, 11:48
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
Z slide Tube

Took all morning looking through scrap but I found it. A 4ft piece of 1x3 for the slider tube backer. Still not exactly sure the correct length.
Attached Images
File Type: jpeg backerrod.jpeg (55.4 KB, 116 views)
Reply With Quote
  #11  
Old Fri 28 April 2017, 20:15
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
No worries got it all sorted.
Reply With Quote
  #12  
Old Sun 30 April 2017, 18:22
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
Okay had a good weekend of it. Got to go to Amarillo tomorrow.
Start again when I get back.
Reply With Quote
  #13  
Old Thu 18 May 2017, 17:52
IamDave
Just call me: Davey
 
Ball Ground, GA
United States of America
Okay Motors and Racks In

I haven't quit just got motors and racks in.
Gonna try and get them mounted over the next week.
Attached Images
File Type: jpg motoranracks.jpg (62.7 KB, 50 views)
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Ball Screw For Sale Francois The Market Place 1 Mon 06 February 2012 23:25
Ball screws Richards Driving Mechanisms: Rack/pinion, gears, screws, belts & chains 1 Sun 28 August 2011 07:31
hobbed or ground rack? southernduckie Rails & Rollers 11 Thu 26 May 2011 08:36
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault Daya Troubleshooting 45 Mon 21 April 2008 01:05
Round shafts & ball slide blocks versus V-rails & V-wheels joepardy Rails & Rollers 28 Fri 07 December 2007 12:41


All times are GMT -6. The time now is 00:14.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.