MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance > Troubleshooting
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Reply
 
Thread Tools
  #1  
Old Tue 26 June 2012, 08:38
Kart
Just call me: Kart
 
Texas
United States of America
pmdx 133 fried

2 boards same place. These are at the x and slave motors. PMDX thinks it might be a part failure. Anybody else seen this? Comments?
Attached Images
File Type: jpg IMG_20120625_152940.jpg (48.7 KB, 241 views)
File Type: jpg IMG_20120625_153208.jpg (53.6 KB, 239 views)

Last edited by Kart; Tue 26 June 2012 at 08:41..
Reply With Quote
  #2  
Old Tue 26 June 2012, 09:15
Gerald D
Just call me: Gerald (retired)
 
Cape Town
South Africa
If your motors hadn't turned before, and the burn happened at first attempt to power motors, then I think your motor wiring is incorrect and something had to give.

Did you unplug the green connectors off the board? If you do this too many times, the friction grip loosens and could start a burn point.
Reply With Quote
  #3  
Old Tue 26 June 2012, 09:48
danilom
Just call me: Danilo #64
 
Novi Sad
Serbia
Lots of dust... fire hazard

the wires look like they'r cooked, so it must have been some "short". Do drives still work?
might been that they put out some voltage across those wires
Reply With Quote
  #4  
Old Tue 26 June 2012, 09:53
MetalHead
Just call me: Mike
 
Columbiana AL
United States of America
How are your motors wired at the other end of the cables?

http://www.mechmate.com/forums/showt...14&postcount=1

This shows the pairing for parallel configuration. (Of course this is during the table project and your pairs will be out on the end of your wires at the motors.)

Also I agree you need to check for a short somewhere in the wiring.

What part number wiring is that?
Reply With Quote
  #5  
Old Tue 26 June 2012, 09:56
danilom
Just call me: Danilo #64
 
Novi Sad
Serbia
oh.. haven't seen that its a Motherboard for Geckodrive. That those are the wires directly to the motors. Something really wrong happened here
Reply With Quote
  #6  
Old Wed 27 June 2012, 04:58
southernduckie
Just call me: Andrew (Duckie)
 
new south wales
Australia
133 wiring

huge current there, are there any other motors hooked up and working? please give us more info like, power supply, motors, when it happened first power on or during use? open the drive and see if there is any damage visible. might give clues
Reply With Quote
  #7  
Old Wed 27 June 2012, 07:30
Richards
Just call me: Mike
 
South Jordan, UT
United States of America
Unless the PMDX-133 was defective, it looks to me like a wiring error occurred. The wiring diagram (Table 2 in section 3.1 of the PMDX-133 manual) shows how to connect the wiring for the A, /A, B and /B connections to the Gecko stepper drives.

To get enough current to produce the kind of heat that caused that much damage means that a short occurred somewhere. I cannot imagine that Steve at PMDX would not have tested his products before shipping, especially something as obvious as a dead short between terminals. It could happen, but I've never seen that kind of error escaping quality control.
Reply With Quote
  #8  
Old Sun 19 August 2012, 13:18
JasonC
Just call me: Jason
 
Soldotna,AK
United States of America
Get the multimeter out and see whats going on.
Reply With Quote
Reply

Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
PMDX 126 BOB Setup MetalHead 70. Control Systems 21 Sat 17 August 2013 22:26
Pmdx-122 sold! IN-WondeR The Market Place 6 Thu 03 January 2013 19:39
New PMDX-126 Dale Murray General - MM Build 5 Tue 17 May 2011 19:44
PMDX-122 vs PMDX-125? salewis 70. Control Systems 6 Fri 06 November 2009 05:16
PMDX-132 instead of the PMDX-122 SteveWellman999 70. Control Systems 23 Mon 02 November 2009 11:47


All times are GMT -6. The time now is 02:53.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.