#1
|
|||
|
|||
Parting Out Old Non MechMate CNC
Hi all,
Need advise as usual. I have a rolling mm that am happy with and plan to complete. A friend has just given me a cosmec NR/E complete in running order, this is far to big for me but has many usable parts. vacum table with pump, control console, 2 drills, 2 spindles and more. Here are several questions I have. 1: Are the spindels to big for the mm, they are 7.5 kw Gloldano-Colombos ? 2: Should i just keep the machine as a whole and sell it for parts, if so where? 3: Should i part the machine out and use as much as i can on my mm. an use a lot of small parts, if i part it out where is the best sites to go to? 4: Has AC tech controller 3 phase, will have to convert the spindels and controlled to 3 phase or use phaes-a-rator for the spindels and controller ? Is this a problem since the remainder of the machine is single phase? The list goes on need any advise and or help will be appriciated. thanks all, Al Drouin |
#2
|
|||
|
|||
Al, is there anything wrong with it? If it was me I would try and find the space to house and use it.
|
#3
|
|||
|
|||
Al
How about posting a picture of it? But I agree with Russell, if you can use it and you have space, I would keep it. |
#4
|
|||
|
|||
no room
The cosmec is a great machine. I have seen it in action. It is fast and accurate but takes up an area of 20' x 30' let alone working area. I am now 61 and I don't I am willing to put in the effort in a new venture... think retire an play with mm a little that is why i am thinking the way i am. It is now sitting outside my garage covered up with the controles and asscessories inside. If some one is interested it would be a great affordable venture for them. Any takers????
thanks. al |
#5
|
|||
|
|||
I managed to get my hands on a cosmec and it is really big.
I need to refurbish it and get it to work after his interface will be changed. |
#6
|
|||
|
|||
I would be interested in the machine myself, where is this machine located? US? what would you be looking to get for it? and what condition do you think it is in?
|
#7
|
|||
|
|||
Never mind, just committed to buy a boatload of parts from David S. on the another post will be broke again for awhile...
|
#8
|
|||
|
|||
final decision dismantel
I have decided to part out my cosmec due to size restrenghts. I will be selling many of the components to mechmate builders. i will provide pictures of the components in the near soon. Here is a very shortlist.
colombo spindels 7.5 kw have 2 desontter drills have 2 vfd ac tech model m12100c 10 hp general vacuum vacuum pump and tank & controles 4hp acme transformer 408v to 208v 75kva numerous other transformers all sizes simens of contactors voltage conditioners advanced motion controls brush type pwm servo amplifier model 30a20act have 3 all types of electrical hardware and much more anyone need anything feel free to contact me thanks al |
#9
|
|||
|
|||
How much for one of those Columbo spindles? Are they with ATC, or Er collet?
|
#10
|
|||
|
|||
they are manual and am looking for $500 ea, i also have aluminiun dust shos for them PM me and i will give details
thanks al |
#11
|
|||
|
|||
Can you post SPECS off of those spindles?
|
#12
|
|||
|
|||
this the information off the pindels are giordand colombo
130 volt 220 180 hz 300 10700 rpm 18000 5 kw 7.5 RV1216.22 FP P54 11.86 19 they are in exelent condition and ran with in the last year all the proper information can be found on the colombo site under the model # RV116 thanks al Last edited by alan254; Sun 30 January 2011 at 07:44.. |
#13
|
|||
|
|||
columbo spindles
I,m New to spindles but have a shop bot with router and am wondering if you have the controllers for these as well. Thanks Don
|
#14
|
|||
|
|||
#15
|
|||
|
|||
this the only one i have , it is listed on the ac tech site all the specks can be seen there.
Thanks |
#16
|
|||
|
|||
hi hutterland,
I do have one vfd fot the spindels that in an ac tech model 12100c thanks al |
#17
|
|||
|
|||
Quote:
Too heavy for the bot z motor |
#18
|
|||
|
|||
Thanks for the info, Don
|
#19
|
|||
|
|||
here are some of the magnetic starters i have for sale from the dismanel.
siemans 3T40 17-0 A 3T42 17-7 A 3TB42 17-0 A 3AU 52 16-25A also have dim strips all lengths and rail terimanal strips |
#20
|
|||
|
|||
Spindles
Do you still have the Colombo spindles?
Thanks |
#21
|
|||
|
|||
just sold them
thanks al |
|
|