![]() |
#1
|
|||
|
|||
Integrated PC & Control Cabinet - Wilmington NC
Hello Everyone
I would like to start off by thanking Gerald for providing the web site and plans for the MechMate.also I would like to thank all the others here for there great post, pictures ,support etc. I am not only speaking for myself when I say I have been dreaming for years about owning a CNC router.I was looking to buy one a few weeks back. while look around the net I found the Shopbot forum after reading for only 10min. I found this site.after reading for a few min. I knew this was what I wanted to build. here I am gathering materials. And not to forget anyone I had the pleasure to met one forum member His name is JR .He is building one nice machine what a great inspiration to meet him and see his work. Thanks JR. My name home town an state below Thanks Gene Wilmington NC cbboatworks@aol.com Last edited by cbboatworks; Wed 04 July 2007 at 08:14.. |
#2
|
|||
|
|||
It has been over 6 months since I said I was going to start my build... well, I did not have much time and lots of other things came up in that 6 months. So now I have finally found the time to start. I started last week with the control box and will post pictures as I go. Please note that the first few pictures are not much to look at but it is a start. My box was inspired by JR & Marc...so, not all my ideas. What I have done is mounted my PC inside of the control box and also have added panel mounted usb hubs and the CDR is accessible from the bottom of the box without having to open the front panel. I have added a touch screen monitor to the box that is also flush mount. I will keep the pictures coming.Please note the cutouts for the Geckos are a little wobbley and have been straightened since that picture was taken.
Thanks ![]() ![]() ![]() Last edited by cbboatworks; Fri 15 February 2008 at 07:14.. |
#3
|
|||
|
|||
That's super sharp Gene. I'm envious.
|
#4
|
|||
|
|||
Thanks Doug for the kind feedback,
Gene |
#5
|
|||
|
|||
Gene,
What a good idea. If you don't mind me asking, where did you get your control box? Did you have to do some mods for air flow? The computer, touchscreen and power supply have to put out some serious heat. Just trying to get some ideas before I jump-in with both feet. I think control box/ power supply are going to be the most difficult for me, still learning. |
#6
|
|||
|
|||
Gene,
Where did you buy your Touch Screen and PC? What you got looks good! |
#7
|
|||
|
|||
Just a few pictures of the box as I am taking it apart and pre pairing it for paint on Tuesday. also I am going to answer this question before anyone ask. the little red momentary switch is to cut the PC on and the two little LED's are part of the onboard PC as well. Thanks
Gene ![]() ![]() ![]() ![]() ![]() |
#8
|
|||
|
|||
Quote:
As much as I would like to take the credit for this idea.. I can't.. The idea come from JR & Marc. as for The heat the Touch Screen puts out no heat. I have four fans that will be mounted behind each gecko to cool them. Thank you for looking Gene |
#9
|
|||
|
|||
Quote:
I bought two of them off of Ebay. both where new. Gene |
#10
|
|||
|
|||
Gene,
Nice work. I like the touch screen. There's no way anyone can build just one MM. So many ideas, your gonna build more. ![]() |
#11
|
|||
|
|||
Elegant Gene, Just elegant.
Bravo.... |
#12
|
|||
|
|||
Gene,
I like the touch screen too. Did you have any problems getting it to run with windows and Mach? Driver issues or anything? |
#13
|
|||
|
|||
Gene, I enjoyed talking on the phone the other day it just reinforces the idea that this machine is whatyou make of it great job and everyone has great ideas it is going to be hard to come up with a final decision on which route to follow.
|
#14
|
|||
|
|||
Quote:
I did not have any problems at all. It took around 5 min to install and start playing. so far it looks and works great. I have a mini key board that I will be using along with the touch screen as well. I will post a few pictures of it. Thanks Gene |
#15
|
|||
|
|||
Quote:
Gene |
#16
|
|||
|
|||
Here is the Key board that I will be using along with the Touch Screen:
![]() ![]() |
#17
|
|||
|
|||
That keyboard will give you tricky "cursor" control for the z-axis, having the page up/down combined with the up/down arrows. Also, you want a Shift button near the cursors for jog speeds. Mach3 is "optimised" for the long keyboard. You will have to get a remote!
![]() ![]() |
#18
|
|||
|
|||
Quote:
Thanks for pointing that out... I did not even notice that there was no shift key near the up/down cursor. if it makes a difference I will be using a shuttle pro II along with the key board. Thanks |
#19
|
|||
|
|||
Gene, there are apparently ways of re-mapping a keyboard's buttons, and I have heard of guys coding their keys with different colours. The arcade game builders are the fundis at this.
The IPAC was all the rage with the Mach guys about 3 years ago - very seldom mentioned these days. (needs a tiny capacitor on each line to make it immune to noise in our environment) |
#20
|
|||
|
|||
It is a great feeling to see some MM blue of my own.
![]() ![]() ![]() ![]() Last edited by cbboatworks; Wed 20 February 2008 at 11:27.. |
#21
|
|||
|
|||
mmmm. automotive paint. nice
![]() |
#22
|
|||
|
|||
Ouch,
My eyes, my eyes. ![]() |
#23
|
|||
|
|||
Sean
The paint is Imron 3.5 HG Industrial. It is used on park rides, industrial machines etc. It is a single stage two part paint great stuff... It is the same as the automotive Imron 5000 but much cheaper. I have been using it for sometime now and love it. Thanks for posting |
#24
|
|||
|
|||
Gene,
Is that paint hard to find? I really like the finish. What kind of thinner does it require? |
#25
|
|||
|
|||
That's absolutely beautiful. Great work.
|
#26
|
|||
|
|||
Quote:
The paint can be bought a most auto paint stores that sell Dupont products. it is a two part paint so you will need to buy the paint,activator and urethane reducer.also if it is cold when you paint you will need a accelerator. Paint is Imron 3.5 HG Activator part# VGM-6005 you need to ask the person at the paint store to give you the same brand of accelerator. (NOTE This is very Toxic paint so Please use a NIOSH Respirator) http://www.bennette.com/pdf/Imron3-5HG.pdf Last edited by cbboatworks; Wed 20 February 2008 at 18:32.. |
#27
|
|||
|
|||
#28
|
|||
|
|||
For the folks that will ask what gun do you use. I have a $550.00 Sata jet Digital 2000...But get this my $14.99 Harbor freight gun puts down a better finish. so if any of you have ?s on what gun to buy. Dig deep into your pockets at get out that $14.99. I use the harbor freight gun on everthing I paint.
47016-4VGA Central Pneumatic Professional 20 OZ. GRAVITY FEED SPRAY GUN. Online the gun is listed for $24.99 in the store it is $14.99 Last edited by cbboatworks; Wed 20 February 2008 at 18:58.. |
#29
|
|||
|
|||
Looks great, Gene. Thanks for the paint job!
![]() |
#30
|
|||
|
|||
Gene,
Interestingly you mention the HF gun at 15 dollars. At my shop, where labor cost more per hour than the cost of 3 guns....I buy these by the case. It's easier to toss-the-gun after spraying some materials than actually cleaning it and paying the guy to sit on the clock and "clean up everything 3 times". ...just the penny pinching boss man talking ![]() |
![]() |
|
|