Forum: Construction started, but not cutting yet
Fri 31 January 2020, 20:03
|
Replies: 232
Views: 225,705
Paul, I'm happy to see people take benefit. ...
Paul, I'm happy to see people take benefit.
I've been meaning to post here for quite some time, professional procrastination at its best.
Many members here have been very generous with there...
|
Forum: Construction started, but not cutting yet
Thu 22 March 2018, 09:19
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Tue 06 February 2018, 19:53
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Tue 06 February 2018, 17:28
|
Replies: 232
Views: 225,705
Will do John,
I've been having an issue with...
Will do John,
I've been having an issue with mach, every time I zero a piece and start cutting, the z is always offset too high by 1.3" .... Its nothing can find in cam software, I'm fairly sure...
|
Forum: Construction started, but not cutting yet
Sun 28 January 2018, 15:04
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Sat 27 January 2018, 17:47
|
Replies: 232
Views: 225,705
Hello all,
Finally, I've done my first cut...
Hello all,
Finally, I've done my first cut of the roadrunner.
I wanted to ask how most of you normally set up your machines as far as home and X0,Y0.
Is "Home" the location the spindle is...
|
Forum: Construction started, but not cutting yet
Sun 14 January 2018, 11:06
|
Replies: 232
Views: 225,705
Thank you Sir!
Trim pot works correctly in...
Thank you Sir!
Trim pot works correctly in clockwise direction now that VFD settings are correct. It was turned all the way down from my last attempt. Re-calibrated and now 9.8v = 400Hz.
In Mach...
|
Forum: Construction started, but not cutting yet
Sat 13 January 2018, 22:26
|
Replies: 232
Views: 225,705
I could never find my model # HY04D023B in any...
I could never find my model # HY04D023B in any manual, its always skipped. but the one you linked is what I've been using.
PD-001 is set to 1, was a typo.
Thank you very much for that blog post,...
|
Forum: Construction started, but not cutting yet
Sat 13 January 2018, 12:25
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Thu 11 January 2018, 13:45
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Thu 11 January 2018, 12:18
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Fri 15 December 2017, 08:30
|
Replies: 232
Views: 225,705
Thanks Brad, sorry for the delay.
I'm...
Thanks Brad, sorry for the delay.
I'm suspicious of my volt meter, its an old digital one but when I went to test ACM to VI again before I starting it in test mode, it showed voltage ramping up to...
|
Forum: Construction started, but not cutting yet
Wed 13 December 2017, 11:21
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Wed 13 December 2017, 09:43
|
Replies: 232
Views: 225,705
ok. more confusion. I made sure trim pot is all...
ok. more confusion. I made sure trim pot is all the way CC before starting system, started test mode and played with pot but nothing would happen. started system with pot turned fully clockwise and...
|
Forum: Construction started, but not cutting yet
Tue 12 December 2017, 20:45
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Tue 12 December 2017, 19:29
|
Replies: 232
Views: 225,705
For some reason my post submission didn't go...
For some reason my post submission didn't go through the other day.
I ended up swapping wiring, you can only reverse the slaved axis in software.
I tried online, came back at 250 not including...
|
Forum: Construction started, but not cutting yet
Mon 11 December 2017, 12:25
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Wed 06 December 2017, 21:42
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Wed 06 December 2017, 15:27
|
Replies: 232
Views: 225,705
Thanks Brad, it doesn't look obsolete. same...
Thanks Brad, it doesn't look obsolete. same parameters as what my manual shows, but I'm not going modbus route. I believe those parameters are modbus only?
and can someone tell me what is a decent...
|
Forum: Construction started, but not cutting yet
Sun 03 December 2017, 09:44
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Sat 02 December 2017, 11:25
|
Replies: 232
Views: 225,705
Hello all,
I've got the spindle spinning...
Hello all,
I've got the spindle spinning from mach3 through a PMDX-107, but cant change RPM through mach3. I used warpd9 smooth stepper settings for mach and set main parameters in VFD, setting...
|
Forum: Construction started, but not cutting yet
Mon 20 November 2017, 10:39
|
Replies: 232
Views: 225,705
Yes Mike, the pk299 move the x & y fine, but...
Yes Mike, the pk299 move the x & y fine, but fairly close to skipping steps( very heavy gantry tubes + y-car stuff). Pk299 wasn't tough enough for the Z's either, that's why I thought I had motor...
|
Forum: Construction started, but not cutting yet
Sun 19 November 2017, 20:07
|
Replies: 232
Views: 225,705
Yes Mike, same issue although not really an...
Yes Mike, same issue although not really an issue, I'm just expecting too much out of the motors.
Pete, first thing I should of done is refamiliarized, but my time is limited and I got impatient....
|
Forum: Construction started, but not cutting yet
Sun 19 November 2017, 16:56
|
Replies: 232
Views: 225,705
|
Forum: Construction started, but not cutting yet
Wed 15 November 2017, 20:04
|
Replies: 232
Views: 225,705
ok, just finished going over voltage...
ok, just finished going over voltage requirements. looks like I'm a bit over the recommended 20%, should i be concerned? although it will match the KL34H280-45-8A @2.2mH inductance much better.
I...
|