Forum: Troubleshooting
Thu 31 May 2018, 10:00
|
Replies: 5
Views: 13,265
Where to get router Repaired or Replaced?
Good routers aren't cheap. If yours isn't under warranty, IMHO, just buck up and get new one.
If you make $$ from it, keep a spare on hand, that way, even if one dies, you can keep making $$,...
|
Forum: CNC motion control software
Sat 21 October 2017, 08:30
|
Replies: 62
Views: 72,202
|
Forum: General - MM Build
Sat 07 October 2017, 07:58
|
Replies: 0
Views: 7,688
Anyone near Clarksville TN ready to get started?
Reality is setting in... I'm not going to build a MechMate. I have a kit of steel that is not opened. If you are local, and would like to build one, private message me and we will discuss getting...
|
Forum: Introduce yourself and start planning
Sat 26 August 2017, 06:36
|
Replies: 18
Views: 37,885
|
Forum: MechMates already cutting
Sat 26 August 2017, 06:33
|
Replies: 454
Views: 435,583
|
Forum: Construction started, but not cutting yet
Wed 01 March 2017, 14:31
|
Replies: 126
Views: 151,922
Yes, there are lotus of ways to do almost...
Yes, there are lotus of ways to do almost everything. The great thing is to get a fine build we don't need the 'most optimum solution' for each thing, we need what works for us!
Don't get to tied...
|
Forum: MechMates already cutting
Sat 25 February 2017, 05:03
|
Replies: 100
Views: 99,734
|
Forum: MechMates already cutting
Fri 03 February 2017, 07:26
|
Replies: 454
Views: 435,583
No experience with this one. Normally, you get...
No experience with this one. Normally, you get what you pay for.
I do purchase things from Bangood or AyliExpress from time to time, but quality I find as variable so be prepared to re-purchase...
|
Forum: MechMates already cutting
Mon 23 January 2017, 10:10
|
Replies: 75
Views: 129,973
|
Forum: MechMates already cutting
Thu 24 November 2016, 13:49
|
Replies: 62
Views: 53,655
|
Forum: 80. Computer Hardware & Software
Thu 03 November 2016, 05:53
|
Replies: 14
Views: 28,698
|
Forum: Dxf Library
Tue 30 August 2016, 14:55
|
Replies: 2
Views: 15,595
|
Forum: Construction started, but not cutting yet
Tue 30 August 2016, 14:49
|
Replies: 126
Views: 151,922
|
Forum: Miscellaneous / General / Whatever / Catchall
Fri 26 August 2016, 07:48
|
Replies: 50
Views: 59,709
|
Forum: MechMates already cutting
Fri 26 August 2016, 07:45
|
Replies: 454
Views: 435,583
Props
Beautiful propellers. ...
|
Forum: Introduce yourself and start planning
Sat 06 August 2016, 09:03
|
Replies: 8
Views: 18,513
My best suggestion is to read, read, then when...
My best suggestion is to read, read, then when you get tired, read the forums more. Oh, did I say there is a lot of stuff on all aspects of CNC here, so keep reading :D
This board stays pretty...
|
Forum: Introduce yourself and start planning
Sat 06 August 2016, 08:56
|
Replies: 8
Views: 18,513
|
Forum: Human Interface Devices (HID's)
Sat 30 July 2016, 16:09
|
Replies: 4
Views: 36,489
|
Forum: MechMates already cutting
Wed 01 June 2016, 08:48
|
Replies: 479
Views: 531,629
Sorry, I didn't communicate clearly. .. Your...
Sorry, I didn't communicate clearly. .. Your intent is what I was 'assuming', but that isn't what I communicated ... my issue.
Keep going ... yep, I like following what you are doing. ... Take care
|
Forum: MechMates already cutting
Wed 01 June 2016, 07:55
|
Replies: 479
Views: 531,629
|
Forum: MechMates already cutting
Tue 31 May 2016, 17:32
|
Replies: 735
Views: 481,533
|
Forum: MechMates already cutting
Tue 31 May 2016, 17:25
|
Replies: 479
Views: 531,629
I think the router mount is removable with one...
I think the router mount is removable with one bolt. Just make an additional mount and put the laser head on it. It should be 'easy swappable' depending on power requirements. Otherwise just mount...
|
Forum: Troubleshooting
Tue 24 May 2016, 11:43
|
Replies: 4
Views: 10,887
After living in Texas with hurricanes and the...
After living in Texas with hurricanes and the tornados they spawn, and in the 'tornado belt' for the rest of my years, moving to Tennessee 10 years ago I have had more lightening, wind, and...
|
Forum: Miscellaneous / General / Whatever / Catchall
Wed 04 May 2016, 20:52
|
Replies: 6
Views: 32,455
|
Forum: Introduce yourself and start planning
Sat 23 April 2016, 13:14
|
Replies: 3
Views: 6,550
Welcome!
The gantry is pretty heavy for a plasma, but it can be done.
One of the options is building a quick change mount for the router, that could be swapped for a plasma head mount.
I know nothing...
|