Forum: Troubleshooting
Mon 21 September 2009, 16:20
|
Replies: 191
Views: 124,146
|
Forum: 60. Wiring & Cable Management
Sun 20 September 2009, 08:51
|
Replies: 221
Views: 224,396
|
Forum: Utility software
Sun 20 September 2009, 07:23
|
Replies: 29
Views: 56,071
|
Forum: Utility software
Fri 18 September 2009, 23:09
|
Replies: 29
Views: 56,071
|
Forum: 20. Gantry
Fri 18 September 2009, 22:59
|
Replies: 11
Views: 17,953
|
Forum: Utility software
Fri 18 September 2009, 22:14
|
Replies: 29
Views: 56,071
|
Forum: MechMates already cutting
Fri 18 September 2009, 16:33
|
Replies: 46
Views: 40,221
Thanks Rene, But I tried that. I think I went...
Thanks Rene, But I tried that. I think I went down to 20 ipm at one point. I wish I made a video of it cutting. At the slower speed you can watch the bit rise up to make the angle than the Z...
|
Forum: Utility software
Fri 18 September 2009, 10:23
|
Replies: 29
Views: 56,071
Just thinking about It, The kreg jig is so fast...
Just thinking about It, The kreg jig is so fast to use and works great that I am not sure if it is worth doing on the MM. If I could get my MM to tie my shoes I probably would:D. But the MM is not...
|
Forum: Utility software
Fri 18 September 2009, 09:36
|
Replies: 29
Views: 56,071
|
Forum: MechMates already cutting
Thu 17 September 2009, 10:24
|
Replies: 46
Views: 40,221
|
Forum: General - MM Operating
Thu 17 September 2009, 00:37
|
Replies: 7
Views: 15,418
"MM test pattern" to check your performance
I have been thinking of the MM test board cut that Gerald mention in a backlash thread. The Idea is to have a file that we could all share and cut on our own MM’s to compare and fine tune our...
|
Forum: MechMates already cutting
Wed 16 September 2009, 22:57
|
Replies: 46
Views: 40,221
|
Forum: MechMates already cutting
Wed 16 September 2009, 00:45
|
Replies: 116
Views: 124,883
|
Forum: General - MM Build
Tue 15 September 2009, 23:02
|
Replies: 25
Views: 25,628
|
Forum: 55. Dust Management
Tue 15 September 2009, 21:39
|
Replies: 17
Views: 23,949
|
Forum: General - MM Build
Tue 15 September 2009, 21:16
|
Replies: 25
Views: 25,628
|
Forum: MechMates already cutting
Tue 15 September 2009, 20:56
|
Replies: 46
Views: 40,221
|
Forum: MechMates already cutting
Tue 15 September 2009, 18:59
|
Replies: 46
Views: 40,221
|
Forum: MechMates already cutting
Tue 15 September 2009, 10:33
|
Replies: 46
Views: 40,221
|
Forum: MechMates already cutting
Tue 15 September 2009, 00:22
|
Replies: 43
Views: 34,285
|
Forum: MechMates already cutting
Mon 14 September 2009, 22:25
|
Replies: 46
Views: 40,221
I gave up on the new computer for the moment. ...
I gave up on the new computer for the moment. Wanted to watch the machine work for a little while.:)
So the guys from aspire tell me that the 3d carving example that they give you with the trial...
|
Forum: MechMates already cutting
Mon 14 September 2009, 18:28
|
Replies: 46
Views: 40,221
:mad::mad::confused::mad::confused::confused:(...
:mad::mad::confused::mad::confused::confused:( smiley face banging his head in to the wall)
Must have reinstalled Mach 5 or 6 times not always the same problem. But now atleast I am back to were...
|
Forum: MechMates already cutting
Mon 14 September 2009, 14:32
|
Replies: 46
Views: 40,221
Thanks Mike I would appreciate that. I have a...
Thanks Mike I would appreciate that. I have a feeling that it is something in Mach causing the problem. I have been prepping a new computer for my machine, (Need more memory and faster CPU to run...
|
Forum: MechMates already cutting
Sun 13 September 2009, 19:25
|
Replies: 46
Views: 40,221
Back with my MM
Well I know I have been slacking in the forum entry area for awhile. But I have still been reading a lot. Went home to New York for awhile now I am back in CA with my Machine.:) Have not had much...
|
Forum: 55. Dust Management
Sun 12 April 2009, 07:48
|
Replies: 8
Views: 17,651
|