MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Showing results 1 to 19 of 19
Search took 0.00 seconds.
Search: Posts Made By: carcan
Forum: Construction started, but not cutting yet Sun 23 July 2017, 00:23
Replies: 9
Views: 15,821
Posted By carcan
Why the X beams are assembled "at the...

Why the X beams are assembled "at the mirror"
Forum: CNC motion control software Thu 04 June 2015, 10:28
Replies: 0
Views: 6,713
Posted By carcan
Free Motion SW & USB HW

A new resource for Motion SW & HW http://www.theremino.com/downloads/automation#cnc
Forum: Troubleshooting Fri 15 May 2015, 10:21
Replies: 49
Views: 57,136
Posted By carcan
Can you explain better ? The only time i had...

Can you explain better ? The only time i had problems is because the small screw on gear was unscrewed
Forum: Introduce yourself and start planning Wed 13 May 2015, 09:22
Replies: 4
Views: 6,701
Posted By carcan
Benvenuto

Benvenuto
Forum: Introduce yourself and start planning Thu 19 February 2015, 07:43
Replies: 7
Views: 7,330
Posted By carcan
Ciao Gianni !!!

Ciao Gianni !!!
Forum: Cutting various materials - bit selection, feeds, speeds Mon 01 December 2014, 14:28
Replies: 15
Views: 17,366
Posted By carcan
Yes, but if the first corner is right, means that...

Yes, but if the first corner is right, means that the CV settings at your speed do not allow to do 90 degree angles. Check the acceleration value, speed and CV settings, otherwise try to cut with a...
Forum: Cutting various materials - bit selection, feeds, speeds Mon 01 December 2014, 13:45
Replies: 15
Views: 17,366
Posted By carcan
I think it is a problem of CV settings

I think it is a problem of CV settings
Forum: Rails & Rollers Tue 01 July 2014, 04:04
Replies: 19
Views: 24,171
Posted By carcan
Steel is hard to work

My C channels are quite straight, but I want they become more planar and perfectly at 90 degrees, in order to reduce the using of shims.
I have two long and very straight (more than 3 metres) pieces...
Forum: 10. Base Table Thu 10 October 2013, 03:55
Replies: 5
Views: 14,596
Posted By carcan
Why not

Instead of using legs why not use two tripod ? (the picture is only a sample)
Forum: 60. Wiring & Cable Management Mon 20 May 2013, 06:58
Replies: 7
Views: 12,372
Posted By carcan
I would use these connectors because I want to...

I would use these connectors because I want to share the electronic box with a hot wire CNC foam cutting machine
Forum: 60. Wiring & Cable Management Tue 14 May 2013, 07:03
Replies: 7
Views: 12,372
Posted By carcan
Heavy duty and cheap motor connectors

To connect motors I bought this cheap (plug & socket only 5 euros) connectors
Forum: 40. Z-Slide Sat 27 April 2013, 02:52
Replies: 17
Views: 36,831
Posted By carcan
My idea is to have a system that you can build...

My idea is to have a system that you can build with the L steel grinded with the "skate". Also you can adjust the parallelism simply with very thin washers.
If you want to change the "nature" of the...
Forum: 40. Z-Slide Fri 01 February 2013, 04:16
Replies: 17
Views: 36,831
Posted By carcan
New Z-Slide or Prefab Rail Ideas!

Instead of using a plate, that is difficult to grind, why we can use two "classic" rails ?
Forum: Rails & Rollers Wed 17 October 2012, 06:22
Replies: 2
Views: 9,145
Posted By carcan
Thanks!!

Thanks!!
Forum: Rails & Rollers Wed 17 October 2012, 03:37
Replies: 2
Views: 9,145
Posted By carcan
Bearing shielded or sealed

On VXB bearings site there are two kind of VGroove bearing:
http://www.vxb.com/page/bearings/PROD/V-Groove-Bearings/Kit8352
and
http://www.vxb.com/page/bearings/PROD/V-Groove-Bearings/Kit8406...
Forum: Profiled (laser cut) & bent steel plate Mon 08 October 2012, 03:18
Replies: 7
Views: 16,316
Posted By carcan
Laser Parts (maybe) available in Italy and I belive in Europe

Hello, I am in contact with an italian company that can cut and bend the steel.

I'm waiting the cost of the complete set, I think that if there are many people interested the price become low.
...
Forum: Introduce yourself and start planning Fri 13 July 2012, 10:45
Replies: 5
Views: 5,733
Posted By carcan
Thank you but bending is also necessary, i am not...

Thank you but bending is also necessary, i am not able to do.
Forum: Introduce yourself and start planning Fri 13 July 2012, 07:58
Replies: 5
Views: 5,733
Posted By carcan
Thank You, I have contacted the user Milkov with...

Thank You, I have contacted the user Milkov with a PM but I never received an answer. I will try again.
Forum: Introduce yourself and start planning Thu 12 July 2012, 15:36
Replies: 5
Views: 5,733
Posted By carcan
Hi to all from Italy

Hi I'm interested in woodworking, I have just discovered the mechmate CNC machine and now I want to build one.
But before start I need to know where in Italy or also in Europe I can find the...
Showing results 1 to 19 of 19

 
Forum Jump

All times are GMT -6. The time now is 05:52.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.