MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Showing results 1 to 9 of 9
Search took 0.00 seconds.
Search: Posts Made By: J.R. Hatcher
Forum: MechMates already cutting Fri 12 November 2010, 06:34
Replies: 550
Views: 150,121
Posted By J.R. Hatcher
Looks great Alan ................... and someone...

Looks great Alan ................... and someone once said I had way to much spare time :D
Forum: MechMates already cutting Fri 05 September 2008, 11:23
Replies: 550
Views: 150,121
Posted By J.R. Hatcher
I am with Heath on the thermal grease for the...

I am with Heath on the thermal grease for the Geckos. I am only pulling 3 amps and mine got surprisingly hot until I installed a fan and I was using thermal grease between gecko and heat sink. I will...
Forum: MechMates already cutting Fri 05 September 2008, 04:05
Replies: 550
Views: 150,121
Posted By J.R. Hatcher
Nice job Alan! I have a question, is the terminal...

Nice job Alan! I have a question, is the terminal end of the Boot lace ferrules solid or hollow?
Forum: MechMates already cutting Sat 16 August 2008, 14:17
Replies: 550
Views: 150,121
Posted By J.R. Hatcher
Alan first thing I want to say is I like your...

Alan first thing I want to say is I like your feet. I was writing a post about feet at the same time you were. After I posted it I looked to see if there were any new post and there was ... yours....
Forum: MechMates already cutting Sun 03 August 2008, 05:54
Replies: 550
Views: 150,121
Posted By J.R. Hatcher
Well, they sure would look good black and the Z...

Well, they sure would look good black and the Z plate too.;):cool:
Forum: MechMates already cutting Sat 02 August 2008, 18:21
Replies: 550
Views: 150,121
Posted By J.R. Hatcher
Alan that looks good, I like the black rails.

Alan that looks good, I like the black rails.
Forum: MechMates already cutting Mon 28 July 2008, 16:36
Replies: 550
Views: 150,121
Posted By J.R. Hatcher
My router has 3/4" mdf bolted to the cross...

My router has 3/4" mdf bolted to the cross members, then a 1/2" mdf plenum (Brady Watson SB style) laying on top of that ..... not attached, then the 3/4" mdf spoil board ..... again not attached. I...
Forum: MechMates already cutting Sat 22 September 2007, 13:44
Replies: 550
Views: 150,121
Posted By J.R. Hatcher
Don't try to cut deep, I found this out the hard...

Don't try to cut deep, I found this out the hard way. The cut will heat up and the 1/16" disc will suffer loss. The first 12' rail I cut down took about 4 disc, the second took almost as many. When I...
Forum: MechMates already cutting Thu 16 August 2007, 05:39
Replies: 550
Views: 150,121
Posted By J.R. Hatcher
Alan could you cut the end off the cable, fit a...

Alan could you cut the end off the cable, fit a rubber gromet in the control box and get a new cable end and hood then solder it on from the inside? The only down side I see to this is if the cable...
Showing results 1 to 9 of 9

 
Forum Jump

All times are GMT -6. The time now is 04:25.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.