Forum: Troubleshooting
Mon 11 September 2017, 01:02
|
Replies: 5
Views: 14,692
|
Forum: Troubleshooting
Thu 07 September 2017, 20:21
|
Replies: 5
Views: 14,692
|
Forum: MechMates already cutting
Thu 07 September 2017, 20:19
|
Replies: 5
Views: 14,162
|
Forum: Troubleshooting
Thu 07 September 2017, 19:48
|
Replies: 5
Views: 14,692
Help please. Consistently looses steps in X.
After cutting my aztec calendar I decided to do some checking and not sure if ths occured after cutting the calendar or has always been there.
Just engraving a rectangle which is meant to be with...
|
Forum: MechMates already cutting
Thu 07 September 2017, 19:30
|
Replies: 5
Views: 14,162
Three years latter and finally cutting.
It has taken me a while and had a large period of doing nothing but have finally got it cutting. First project Aztec calendar. Quite happy with the results. Thanks for Youtuber CNCNUTZ (Peter...
|
Forum: Construction started, but not cutting yet
Mon 25 January 2016, 18:31
|
Replies: 28
Views: 41,287
|
Forum: Introduce yourself and start planning
Thu 29 October 2015, 02:55
|
Replies: 21
Views: 24,187
|
Forum: Construction started, but not cutting yet
Tue 13 October 2015, 23:26
|
Replies: 28
Views: 41,287
I have never used any type of linear shafting...
I have never used any type of linear shafting before but what I have read the round shaft rails are easier to set up than the rectangular type. I certainly had no problem getting them straight and...
|
Forum: Test Area for this forum
Sun 06 September 2015, 05:17
|
Replies: 7
Views: 38,440
Did nothing tried using irfan on one but...
Did nothing tried using irfan on one but couldn't get it to save for some reason and so just thought I would post them into the test area and all worked straight out of the phone
|
Forum: Construction started, but not cutting yet
Sun 06 September 2015, 04:07
|
Replies: 28
Views: 41,287
The easy works done now for the hard stuff.
Glad I don't pay myself by the hour. It has taken me two months to get the table built but happy with the results so far. Reasonably square but haven't leveled it yet but have the feet on so that...
|
Forum: Test Area for this forum
Sun 06 September 2015, 03:52
|
Replies: 7
Views: 38,440
|
Forum: Construction started, but not cutting yet
Sun 19 July 2015, 04:20
|
Replies: 69
Views: 103,243
Thanks for the photos. Already have the...
Thanks for the photos. Already have the supported linear rails and when I got looking into it found it was cheaper to go with ball screw from china than ACME threaded rod and anti-backlash nuts. Do...
|
Forum: Construction started, but not cutting yet
Sat 18 July 2015, 04:22
|
Replies: 69
Views: 103,243
|
Forum: Construction started, but not cutting yet
Tue 14 July 2015, 16:41
|
Replies: 28
Views: 41,287
|
Forum: Test Area for this forum
Tue 14 July 2015, 16:38
|
Replies: 7
Views: 38,440
Yes I was using Apple I phone. Funny thing was...
Yes I was using Apple I phone. Funny thing was when I inverted the picture in Iranview and uploaded it was still inverted. Found all I had to do was load into Ifranview and then save it to correct...
|
Forum: Test Area for this forum
Tue 14 July 2015, 05:56
|
Replies: 7
Views: 38,440
|
Forum: Construction started, but not cutting yet
Tue 14 July 2015, 05:44
|
Replies: 28
Views: 41,287
|
Forum: Construction started, but not cutting yet
Mon 13 July 2015, 23:14
|
Replies: 28
Views: 41,287
Toowoomba Build commenced
Not much activity on this board anymore is there. Or is everybody lurking?
I have taken delivery of all my steel and fasteners and many of my other components. Got held up waiting for the special...
|
Forum: Construction started, but not cutting yet
Sat 04 July 2015, 07:52
|
Replies: 28
Views: 41,287
First Changes in my plan and progress report
Thanks Mike Yeah didn't think I would get way with it but worth a try :).
Well almost a week in and have made some changes to my ideas already.
I have decided that I will go with the Profile cut...
|
Forum: Construction started, but not cutting yet
Tue 30 June 2015, 16:46
|
Replies: 28
Views: 41,287
Thanks Al,
Yes that was a very...
Thanks Al,
Yes that was a very 'interesting' day. I could not get to work that day because of earlier rain had flooded a local creek. I actually live down the bottom of the range in Withcott...
|
Forum: Construction started, but not cutting yet
Tue 30 June 2015, 06:05
|
Replies: 28
Views: 41,287
Hi from Toowoomba Australia
Hi everyone,
I was going to start this build about 5 years ago but went back to work full time but I have now retired (again) and am ready to start. I have searched many different types of CNC...
|
Forum: General - MM Build
Thu 08 December 2011, 16:18
|
Replies: 55
Views: 99,164
|
Forum: General - MM Build
Thu 08 December 2011, 05:59
|
Replies: 55
Views: 99,164
|
Forum: General - MM Build
Wed 07 December 2011, 04:19
|
Replies: 55
Views: 99,164
|
Forum: General - MM Build
Wed 07 December 2011, 03:43
|
Replies: 55
Views: 99,164
|