Forum: MechMates already cutting
Mon 22 February 2016, 22:17
|
Replies: 303
Views: 186,059
|
Forum: MechMates already cutting
Tue 05 March 2013, 12:22
|
Replies: 303
Views: 186,059
|
Forum: MechMates already cutting
Tue 05 March 2013, 08:40
|
Replies: 303
Views: 186,059
That's is about half an hour by car from my...
That's is about half an hour by car from my place, it would have been nice to personally meet indeed, any chance you are coming again ?
During the course of building MM I got addicted to this...
|
Forum: MechMates already cutting
Wed 17 October 2012, 02:02
|
Replies: 130
Views: 96,242
|
Forum: MechMates already cutting
Fri 05 October 2012, 23:23
|
Replies: 130
Views: 96,242
Ken, just to rule out problem with BOB, Wiring...
Ken, just to rule out problem with BOB, Wiring and Computer Cable, assign each outpput pin as x-axis DIrection in mach (one by one) and use a multimeter to check changing level at BOB terminals (at...
|
Forum: MechMates already cutting
Fri 05 October 2012, 13:55
|
Replies: 130
Views: 96,242
|
Forum: MechMates already cutting
Fri 05 October 2012, 13:41
|
Replies: 130
Views: 96,242
|
Forum: MechMates already cutting
Thu 05 January 2012, 07:26
|
Replies: 271
Views: 196,935
|
Forum: 70. Control Systems
Wed 14 December 2011, 13:02
|
Replies: 14
Views: 16,495
|
Forum: 70. Control Systems
Tue 13 December 2011, 07:54
|
Replies: 14
Views: 16,495
I did use an AVR (atmel mega 8) to combine all...
I did use an AVR (atmel mega 8) to combine all proxy and buttons on my mechmate. Beware not to use weak pullups (internal pullups) if needed, when using micros, noise easily can get in and trigger...
|
Forum: 701. Motor Drives
Wed 30 November 2011, 02:33
|
Replies: 13
Views: 19,355
Thanks Ken for your keen interest, basically...
Thanks Ken for your keen interest, basically drivers are protected for current at the outputs making them protected from over-current, miss wiring and short circuits at the output.
So you can only...
|
Forum: 701. Motor Drives
Wed 30 November 2011, 02:16
|
Replies: 13
Views: 19,355
|
Forum: MechMates already cutting
Sun 20 November 2011, 07:23
|
Replies: 271
Views: 196,935
Rik, I made the rollers on small lathe without...
Rik, I made the rollers on small lathe without much problem, the only difficult part was removing a lot of metal on this small lathe as I started with thicker slices than required. You can look for...
|
Forum: Introduce yourself and start planning
Wed 13 July 2011, 13:24
|
Replies: 26
Views: 17,976
86HS9801 is 8 wire motor and you can connect...
86HS9801 is 8 wire motor and you can connect coils in parallel, effectively reducing the inductance in half and can be used at lower dive voltage. Even in this case 24V is not enough to get max...
|
Forum: MechMates already cutting
Sun 03 July 2011, 10:53
|
Replies: 303
Views: 186,059
Just to say hello :)
Hello everyone, been busy and not able to follow, seems like there have been many numbers after me. Trying to catch up ...
|
Forum: MechMates already cutting
Tue 22 June 2010, 04:07
|
Replies: 303
Views: 186,059
A little update :)
Polished and installed the divider screen, This is my first attempt in staining and polishing so nothing creative..
9890
|
Forum: Introduce yourself and start planning
Tue 15 June 2010, 03:03
|
Replies: 28
Views: 24,076
|
Forum: MechMates already cutting
Wed 31 March 2010, 06:34
|
Replies: 303
Views: 186,059
Thanks Jit, PM'ed you.
As the MM seems...
Thanks Jit, PM'ed you.
As the MM seems functional now, I am trying to learn more about stepper and servo drives in order to make driver using descrete components that's not limited by 3A limit of...
|
Forum: MechMates already cutting
Wed 10 March 2010, 10:53
|
Replies: 303
Views: 186,059
|
Forum: MechMates already cutting
Wed 10 March 2010, 10:01
|
Replies: 303
Views: 186,059
Hi Jit,
I don't think you can get Geckos in...
Hi Jit,
I don't think you can get Geckos in India, you need to import like others or like me you can go DIY route now and may be later get Gecko if you feel so :)
I am happy with my drives and...
|
Forum: MechMates already cutting
Mon 08 March 2010, 08:43
|
Replies: 303
Views: 186,059
There is nothing wrong with making lid with MM...
There is nothing wrong with making lid with MM because that what MM is intended to do, cutting curves :) !!
There is not going to be NEXT machine as I have no space left for that, but for sure...
|
Forum: MechMates already cutting
Sun 07 March 2010, 09:44
|
Replies: 303
Views: 186,059
DS works great :)
Thanks Nils :)
Moving to MM, could not complete dust foot today but flexible pipe and dust separator installed and it works great :)
I was amazed to see no dust in vac bag at all, all the dust...
|
Forum: MechMates already cutting
Fri 05 March 2010, 14:30
|
Replies: 303
Views: 186,059
Another one :)
Oops, I said next is dust foot :D but kids wanted something to play !!
8788
|
Forum: MechMates already cutting
Fri 05 March 2010, 14:28
|
Replies: 152
Views: 154,686
|
Forum: MechMates already cutting
Fri 05 March 2010, 09:38
|
Replies: 303
Views: 186,059
|