Forum: The Show Room
Fri 10 December 2010, 07:46
|
Replies: 19
Views: 27,893
|
Forum: MechMates already cutting
Fri 10 December 2010, 07:43
|
Replies: 171
Views: 112,738
|
Forum: Miscellaneous / General / Whatever / Catchall
Thu 25 November 2010, 06:41
|
Replies: 1
Views: 4,520
Chris,
Your phone is the last thing you...
Chris,
Your phone is the last thing you need to worry about. Web site, emails, newsletters, etc. etc. etc. have been gathering more information than I can even begin to touch on in a post.
...
|
Forum: MechMates already cutting
Mon 22 November 2010, 05:43
|
Replies: 1,586
Views: 1,029,724
Ken,
That's interesting. I have never...
Ken,
That's interesting. I have never broken a bit. I've driven a couple of bits into the material and once watched a 1/2" end mill collide with a metal clamp (that was fun :rolleyes:).
...
|
Forum: MechMates already cutting
Sun 21 November 2010, 21:18
|
Replies: 1,586
Views: 1,029,724
|
Forum: MechMates already cutting
Sun 21 November 2010, 14:59
|
Replies: 1,586
Views: 1,029,724
|
Forum: MechMates already cutting
Sun 21 November 2010, 10:37
|
Replies: 1,586
Views: 1,029,724
|
Forum: MechMates already cutting
Sun 21 November 2010, 07:03
|
Replies: 1,586
Views: 1,029,724
Thanks Kobus,
That helps allot. Most of...
Thanks Kobus,
That helps allot. Most of our parameters are the same. The 120 mm/sec is screaming. :eek:
My feedrate for the finish cut is 180 ipm. I came up with that feedrate from the...
|
Forum: MechMates already cutting
Sat 20 November 2010, 20:24
|
Replies: 85
Views: 128,918
|
Forum: MechMates already cutting
Sat 20 November 2010, 18:28
|
Replies: 1,586
Views: 1,029,724
|
Forum: Troubleshooting
Thu 18 November 2010, 06:55
|
Replies: 41
Views: 38,879
|
Forum: General - MM Operating
Wed 17 November 2010, 14:49
|
Replies: 2
Views: 11,031
Thanks Bud,
The issue was me again. I had...
Thanks Bud,
The issue was me again. I had set my "look ahead" to 5 lines when I was cutting allot of profiles. Don't ask why, I now know there are better way for what I was trying to do.
...
|
Forum: 80. Computer Hardware & Software
Wed 17 November 2010, 14:38
|
Replies: 19
Views: 23,541
|
Forum: Troubleshooting
Wed 17 November 2010, 09:15
|
Replies: 41
Views: 38,879
|
Forum: Troubleshooting
Wed 17 November 2010, 09:09
|
Replies: 41
Views: 38,879
|
Forum: General - MM Operating
Wed 17 November 2010, 09:03
|
Replies: 2
Views: 11,031
Mach 3 CV settings
I'm cutting some 3D models using Cut3D and need to speed my cut times up (or is it decrease my cut times, :) ). I came upon this 3 page document on the Mach forum describing CV settings. Its a good...
|
Forum: MechMates already cutting
Fri 12 November 2010, 14:48
|
Replies: 551
Views: 508,959
|
Forum: MechMates already cutting
Thu 11 November 2010, 06:37
|
Replies: 556
Views: 539,980
|
Forum: MechMates already cutting
Tue 09 November 2010, 07:39
|
Replies: 551
Views: 508,959
|
Forum: MechMates already cutting
Sat 06 November 2010, 20:22
|
Replies: 100
Views: 103,496
|
Forum: MechMates already cutting
Thu 28 October 2010, 14:41
|
Replies: 100
Views: 103,496
Steve,
I've been using Vcarve Pro for a...
Steve,
I've been using Vcarve Pro for a year or so. Great program, in my opinion. I set my Z = 0.000 at the top of the part I'm making. All cutting is in the negative Z direction. Just my...
|
Forum: Miscellaneous / General / Whatever / Catchall
Wed 27 October 2010, 07:05
|
Replies: 14
Views: 11,754
I'm currently making sample texture panels to...
I'm currently making sample texture panels to show local cabinet shops. It does take some time to generate the patterns. With Rhino and Vcarve Pro, its not difficult at all, but does require allot...
|
Forum: MechMates already cutting
Thu 21 October 2010, 07:20
|
Replies: 100
Views: 103,496
|
Forum: MechMates already cutting
Wed 20 October 2010, 13:09
|
Replies: 100
Views: 103,496
|
Forum: MechMates already cutting
Wed 20 October 2010, 07:47
|
Replies: 551
Views: 508,959
Thank Nils,
Haven't done allot of plastics,...
Thank Nils,
Haven't done allot of plastics, but I'm sure the time will come.
I'm finally getting my cut quality on hard woods down. Allot less sanding and minimal machine marks.
Funny...
|