MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 7 of 7
Search took
0.00
seconds.
Search:
Posts Made By:
musicworld1
Forum:
70. Control Systems
Tue 28 September 2010, 18:55
Replies:
19
TIP142 Stepper motor driver
Views:
19,327
Posted By
musicworld1
TIP142 Stepper motor driver
I am going to build following circuit to run stepper motor using TIP142. So is there any need to change any thing in this circuit? The schematic of circuit is attached with this post.
Forum:
70. Control Systems
Fri 10 September 2010, 22:59
Replies:
19
TIP142 Stepper motor driver
Views:
19,327
Posted By
musicworld1
There is the address of pic ...
There is the address of pic
http://www.edaboard.com/attachments/13348-uln2003_756-jpg
Forum:
70. Control Systems
Fri 10 September 2010, 12:16
Replies:
19
TIP142 Stepper motor driver
Views:
19,327
Posted By
musicworld1
Using TIP142 insteed of TIP120 to run stepper motor.
I am going to use TIP142 in steed of TIP120 in the following picture and want to operate the stepper at 24V. so which resistor I should use? Or what is the rule of thumb to use resistor. ...
Forum:
70. Control Systems
Tue 24 August 2010, 06:24
Replies:
19
TIP142 Stepper motor driver
Views:
19,327
Posted By
musicworld1
Using power transistors like TIP120 is also...
Using power transistors like TIP120 is also batter. But would you like to suggest me a good professional design of stepper deriver of medium level? You may suggest more than one.
Forum:
70. Control Systems
Wed 04 August 2010, 01:51
Replies:
19
TIP142 Stepper motor driver
Views:
19,327
Posted By
musicworld1
I find some thing written on my motor. That is: ...
I find some thing written on my motor. That is:
60C 45
5 DEG 13 (ohm) MAS
You can also read more about this motor from http://www.compucanjes.com/products/view/14268.html. what is basic formula to...
Forum:
70. Control Systems
Sat 17 July 2010, 03:57
Replies:
19
TIP142 Stepper motor driver
Views:
19,327
Posted By
musicworld1
I have found the reason not the solution, it is...
I have found the reason not the solution, it is that I am using the computer power supply. The +12V point has 6 Amp, as written on info sticker of computer power supply. But ULN2003 require only 0.5...
Forum:
70. Control Systems
Thu 08 July 2010, 04:56
Replies:
19
TIP142 Stepper motor driver
Views:
19,327
Posted By
musicworld1
Unipolar stepper motor with ULN2003?
hi
Last time I was designing like this http://www.eleccircuit.com/wp-content/uploads/2008/05/uln2003-control-stepper-motor-by-parallel-port.jpg. I attack this to computer before start computer....
Showing results 1 to 7 of 7
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
08:20
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.