MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 9 of 9
Search took
0.00
seconds.
Search:
Posts Made By:
drinksalot
Forum:
MechMates already cutting
Sun 20 December 2009, 10:59
Replies:
160
The most beautiful thing that you will see today! #61 - Athens, Greece
Views:
102,230
Posted By
drinksalot
¬¬¬¬¬¬¬*¬**
¬¬¬¬¬¬¬*¬**
Forum:
Construction started, but not cutting yet
Sat 19 December 2009, 07:39
Replies:
18
Mechmate build - Wexford Ireland.
Views:
19,083
Posted By
drinksalot
Thanks Gerald. The plastic in my wallet is...
Thanks Gerald. The plastic in my wallet is certainly getting excercised this month.
Gerry
Forum:
Construction started, but not cutting yet
Sat 19 December 2009, 04:33
Replies:
18
Mechmate build - Wexford Ireland.
Views:
19,083
Posted By
drinksalot
Hello all. I am just about to order based on...
Hello all.
I am just about to order based on the above advise for my setup a 65vdc 15 amp unregulated keling power supply. Are there any problems with this choice. Thanks Gerry
...
Forum:
Construction started, but not cutting yet
Thu 17 December 2009, 16:46
Replies:
18
Mechmate build - Wexford Ireland.
Views:
19,083
Posted By
drinksalot
Thanks Gerald and Graham. I am sorting through...
Thanks Gerald and Graham. I am sorting through all the info at the moment. I hope to have the power supply sorted in the next few days. Then its time for the kitchen project. I received my laser cut...
Forum:
Construction started, but not cutting yet
Wed 16 December 2009, 17:38
Replies:
18
Mechmate build - Wexford Ireland.
Views:
19,083
Posted By
drinksalot
I am using qty 4..Gecko 203v with qty 1..PMDX-122...
I am using qty 4..Gecko 203v with qty 1..PMDX-122 and 4qty 34hs9801 motors. Can some one tell me what power supply to order and maybe where to buy it from. Euro zone. Thanks
Gerry
Forum:
Construction started, but not cutting yet
Thu 10 December 2009, 12:19
Replies:
18
Mechmate build - Wexford Ireland.
Views:
19,083
Posted By
drinksalot
Hello Ken. I hadn't tried it but you got me...
Hello Ken. I hadn't tried it but you got me curious and as the hoist was in position I moved it to above one corner and started to lift. It was about 40 mm off the ground before the oposite side...
Forum:
Construction started, but not cutting yet
Thu 10 December 2009, 02:41
Replies:
18
Mechmate build - Wexford Ireland.
Views:
19,083
Posted By
drinksalot
Hello Ken. I am not sure what shs is but the...
Hello Ken. I am not sure what shs is but the cross channel is 75mm x 38mm welded to the 7inch x 4inch heavy channel I propped and clamped the steel and welded from the top. "Right side up". I hoisted...
Forum:
Construction started, but not cutting yet
Wed 09 December 2009, 17:18
Replies:
18
Mechmate build - Wexford Ireland.
Views:
19,083
Posted By
drinksalot
Thanks Greeny. I have the laser cut parts, the...
Thanks Greeny. I have the laser cut parts, the gecko g302v and the v bearings arriving next week. Time to clean the shed so I can make another mess.
Regards
Gerry
Forum:
Construction started, but not cutting yet
Wed 09 December 2009, 05:13
Replies:
18
Mechmate build - Wexford Ireland.
Views:
19,083
Posted By
drinksalot
Mechmate build - Wexford Ireland.
Hello All
I have been reading this forum for a couple of months now and I want to say thanks to Gerald and all who post on this forum for the wealth of information you have made available.
I...
Showing results 1 to 9 of 9
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
06:09
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.