Forum: The Market Place
Wed 17 August 2022, 00:28
|
Replies: 0
Views: 1,607
|
Forum: 70. Control Systems
Wed 26 May 2010, 07:35
|
Replies: 19
Views: 23,321
Sorry Guys,
I could not resist.
Here is my...
Sorry Guys,
I could not resist.
Here is my link http://www.mechmate.com/forums/showthread.php?t=556
have no issues regarding heat or noise, more than 1.5 yrs passed. Hours of daily work.
The...
|
Forum: MechMates already cutting
Mon 04 January 2010, 06:22
|
Replies: 303
Views: 182,676
|
Forum: MechMates already cutting
Sun 03 January 2010, 17:30
|
Replies: 356
Views: 219,026
|
Forum: MechMates already cutting
Tue 29 December 2009, 17:55
|
Replies: 303
Views: 182,676
|
Forum: MechMates already cutting
Sun 27 December 2009, 09:44
|
Replies: 356
Views: 219,026
|
Forum: MechMates already cutting
Sun 27 December 2009, 09:29
|
Replies: 356
Views: 219,026
Irfan,
Doesn't putty shrink when dry ?
I...
Irfan,
Doesn't putty shrink when dry ?
I am asking becoz I am using other material sometimes there is gap, which can be filled with putty or putty may be used as inlay material.
Nice work.
|
Forum: Troubleshooting
Sun 27 December 2009, 09:22
|
Replies: 25
Views: 20,080
Irfan,
I also use same method as Nils and...
Irfan,
I also use same method as Nils and Kobus, note down line # or find out which segment was being cut in mach .While restarting run from few lines back.
I also run Z zero routine.
|
Forum: MechMates already cutting
Tue 22 December 2009, 08:47
|
Replies: 303
Views: 182,676
|
Forum: MechMates already cutting
Tue 24 November 2009, 19:32
|
Replies: 303
Views: 182,676
So you consumed all discs we purchased :) ...
So you consumed all discs we purchased :)
Just to add I got another bigger pulley from M. bazar.
You also need to check angle for v cutting.
(Note - I was with Anil on 23.11.09 together we...
|
Forum: 10. Base Table
Mon 23 November 2009, 19:20
|
Replies: 75
Views: 107,333
|
Forum: 10. Base Table
Sun 22 November 2009, 20:07
|
Replies: 75
Views: 107,333
|
Forum: 10. Base Table
Tue 17 November 2009, 19:10
|
Replies: 75
Views: 107,333
Length
Nader,
Could you verify length of these parts?
Thanks,
|
Forum: MechMates already cutting
Mon 09 November 2009, 17:37
|
Replies: 303
Views: 182,676
|
Forum: MechMates already cutting
Sun 08 November 2009, 18:39
|
Replies: 303
Views: 182,676
Hi Anil,
Vow fast progress,
If you are...
Hi Anil,
Vow fast progress,
If you are using these steppers, then these are only about 300 oz-in (2.5V-4.6A).
HSS bits even doesn't work on MDF, no match for carbide. I am using all carbide bits.
|
Forum: 10. Base Table
Fri 06 November 2009, 15:42
|
Replies: 75
Views: 107,333
Nader
I used pk296sg7.2 . May be you should...
Nader
I used pk296sg7.2 . May be you should power up motors to check backlash. I see backlash when no power, but while working or holding, I see no backlash or its effect on work.
I am not...
|
Forum: MechMates already cutting
Tue 27 October 2009, 08:28
|
Replies: 303
Views: 182,676
Ani
My sincere advice get gecko 203,...
Ani
My sincere advice get gecko 203, bulletproof. I also tried lot of other things and gave up with (thankfully) Irfan's help. Any other steppers will work.
I also could not import, so got help...
|
Forum: MechMates already cutting
Tue 27 October 2009, 08:08
|
Replies: 303
Views: 182,676
|
Forum: MechMates already cutting
Tue 27 October 2009, 07:50
|
Replies: 303
Views: 182,676
Hi Anil,
Welcome.
You can also find...
Hi Anil,
Welcome.
You can also find capacitors, control boxes, carbide tools etc. at dirt price. Just check them before purchasing. There are two shops in mid of Meena Bazar having thousands of...
|
Forum: 80. Computer Hardware & Software
Tue 22 September 2009, 07:33
|
Replies: 12
Views: 16,840
Another good reading about tweaking XP is here...
Another good reading about tweaking XP is here http://www.askvg.com/master-tutorial-to-make-your-windows-xp-super-fast/
I use dedicated PC with all unused peripherals like LAN, audio turned off....
|
Forum: 20. Gantry
Tue 22 September 2009, 07:17
|
Replies: 11
Views: 16,729
|
Forum: 20. Gantry
Sat 19 September 2009, 06:34
|
Replies: 11
Views: 16,729
Simple solution
Not very beautiful one but simpler and working solution. Made out of readily available items.
Required -
1. GI/Alu/Iron sheet fair thickness 4"x3" (or 4" for proper height)
2. Felt pad of...
|
Forum: General - MM Operating
Fri 18 September 2009, 19:54
|
Replies: 17
Views: 39,245
Yes you are right there, thanks to Gerald for...
Yes you are right there, thanks to Gerald for that he has foreseen the necessity and put the provisions.
But you taught us what is required, how to connect and how to put them on MM :)
In fact...
|
Forum: General - MM Operating
Fri 18 September 2009, 19:13
|
Replies: 17
Views: 39,245
|
Forum: 55. Dust Management
Thu 17 September 2009, 17:48
|
Replies: 30
Views: 36,615
|