MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Showing results 1 to 23 of 23
Search took 0.00 seconds.
Search: Posts Made By: kwang90020
Forum: Troubleshooting Mon 12 December 2011, 22:34
Replies: 9
Views: 13,495
Posted By kwang90020
The machine was not stopped mid process. It was...

The machine was not stopped mid process. It was cutting and moving to another path but did not move all the way but 20 inches short. All the cutting was correct before the move.
If I was feeding too...
Forum: Troubleshooting Sun 11 December 2011, 13:54
Replies: 9
Views: 13,495
Posted By kwang90020
It was in relative mode.

It was in relative mode.
Forum: Troubleshooting Sun 11 December 2011, 13:14
Replies: 9
Views: 13,495
Posted By kwang90020
Zero point changes while cutting

I need help on home zero changes middle of cutting.
I searched the forum but could not find the same problems.:o
I finally finished with machine and tried to cut test patterns.
It's working fine...
Forum: Troubleshooting Tue 17 March 2009, 13:21
Replies: 11
Views: 11,415
Posted By kwang90020
Gerald and Richard, Oops, I made a mistake. My...

Gerald and Richard,
Oops, I made a mistake. My motor is PK296A2A not PK296A1A.
I changed the resistorsto 33k and mm is running fine.
Those resistors make big difference!
I thank you guys again...
Forum: Troubleshooting Sat 14 March 2009, 22:10
Replies: 11
Views: 11,415
Posted By kwang90020
Thanks, Mike and Gerald. I have to change the...

Thanks, Mike and Gerald.
I have to change the capacitor. I have one cap and it is only rated 50V.
I'll make the changes and give you the update.
Thanks again for your help.
Forum: Troubleshooting Sat 14 March 2009, 17:58
Replies: 11
Views: 11,415
Posted By kwang90020
I'm currently using 40V by parallel connection,...

I'm currently using 40V by parallel connection, so if I connect them in serial it will be 80V. Do you think that is too much voltage?

My resistor is fine then, right?

Thanks.
Forum: Troubleshooting Sat 14 March 2009, 10:13
Replies: 11
Views: 11,415
Posted By kwang90020
Gerald, Thank you for the reply. The motor...

Gerald,

Thank you for the reply.
The motor is wired half coil.
Power supply is 40V and the resistor is 12k Ohm.
Forum: Troubleshooting Fri 13 March 2009, 19:25
Replies: 11
Views: 11,415
Posted By kwang90020
Cannot get good jog speeds - first thought PS voltage too low, then current error

I'm about to complete the mm thanks to this excellent website but having problem configuring mach3.
I set mach3 with configuration according to Gear Speed Steps Freq Calculator but I can't get the...
Forum: 40. Z-Slide Thu 11 December 2008, 22:25
Replies: 12
Views: 19,011
Posted By kwang90020
Thank you for the information. krod

Thank you for the information.
krod
Forum: 40. Z-Slide Thu 11 December 2008, 22:04
Replies: 12
Views: 19,011
Posted By kwang90020
Robert, I'm sorry if I made a mistake. I didn't...

Robert,
I'm sorry if I made a mistake. I didn't have experience with forums. Maybe it's a silly question but I have no experience with gas springs. Anyway, I'm also trying to make MM with 24" travel...
Forum: 40. Z-Slide Thu 11 December 2008, 17:46
Replies: 12
Views: 19,011
Posted By kwang90020
Hi, Is it possible to connect two gas springs...

Hi,
Is it possible to connect two gas springs in serial?
Like screw one to the other one using rod coupler.
krod
Forum: Archives Mon 14 April 2008, 12:12
Replies: 21
Views: 21,538
Posted By kwang90020
If I use two guage plates as shown in the pic,...

If I use two guage plates as shown in the pic, would that strengthen the z axis?
Forum: Archives Thu 20 March 2008, 22:36
Replies: 151
Views: 108,202
Posted By kwang90020
I received mine yesterday. It fits good. Joe,...

I received mine yesterday. It fits good. Joe, Great job. Thanks.
Forum: Archives Sun 17 February 2008, 22:27
Replies: 151
Views: 108,202
Posted By kwang90020
Joe, I would like to add bearings to my set...

Joe,
I would like to add bearings to my set also.
Thanks,
Krod
Forum: Archives Sun 03 February 2008, 15:11
Replies: 151
Views: 108,202
Posted By kwang90020
Count me in for a set too. 91748

Count me in for a set too.
91748
Forum: Profiled (laser cut) & bent steel plate Wed 23 January 2008, 15:31
Replies: 24
Views: 32,553
Posted By kwang90020
Curt, Can you check the shipping to Los...

Curt,

Can you check the shipping to Los Angeles, 91748?

Krod
Forum: Profiled (laser cut) & bent steel plate Wed 16 January 2008, 09:48
Replies: 24
Views: 32,553
Posted By kwang90020
Please add me to the list also. Thanks Krod

Please add me to the list also.
Thanks
Krod
Forum: 40. Z-Slide Mon 07 January 2008, 22:08
Replies: 25
Views: 37,510
Posted By kwang90020
Gerald, What do you think is best way to...

Gerald,
What do you think is best way to increase the under gantry clearance?
Forum: Profiled (laser cut) & bent steel plate Mon 07 January 2008, 08:26
Replies: 24
Views: 32,422
Posted By kwang90020
Sean, I'm interested in immediate purchase.

Sean,
I'm interested in immediate purchase.
Forum: Profiled (laser cut) & bent steel plate Sun 06 January 2008, 19:29
Replies: 24
Views: 32,422
Posted By kwang90020
Nils, I would like to purchase a set and...

Nils,

I would like to purchase a set and shipped to Los Angels.
How much would be the shipping?

Krod
Forum: Profiled (laser cut) & bent steel plate Mon 31 December 2007, 13:28
Replies: 29
Views: 34,623
Posted By kwang90020
Smile Thanks for the info. Just make sure. Is 10 20...

Thanks for the info.
Just make sure.
Is 10 20 454 became two drawings which are 10 20 451 and 10 20 452?
Happy new year! :)
Forum: Profiled (laser cut) & bent steel plate Sat 29 December 2007, 11:31
Replies: 24
Views: 32,553
Posted By kwang90020
I would like to have the set cut also. I'm in...

I would like to have the set cut also. I'm in California and would like to know how heavy or how much shipping will be.
Forum: Profiled (laser cut) & bent steel plate Fri 28 December 2007, 19:31
Replies: 29
Views: 34,623
Posted By kwang90020
Hi, I'm posting for the first time and trying...

Hi,
I'm posting for the first time and trying to figure out where the drawing 10 20 454 is. I could not find it in zipped files nor in pdf files. It wasn't even in the spread sheet.
Thanks
Showing results 1 to 23 of 23

 
Forum Jump

All times are GMT -6. The time now is 15:06.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.