Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Mon 25 March 2019, 10:21
|
Replies: 1
Views: 25,675
pinion Gears
I would not want to harden them, it will wear out your rack sooner. I have gone through 1 set in 10 years rack still looks good.
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Sat 09 March 2019, 17:32
|
Replies: 449
Views: 471,123
Belt Drive update
I put these belt drives on my machine in late 2009 I use my machine every day and cut a wide range of products, today 3/9/2019 is the first day I have had to do anything with my belt drives as I...
|
Forum: 10. Base Table
Thu 18 December 2014, 20:47
|
Replies: 8
Views: 15,652
|
Forum: Troubleshooting
Sun 10 February 2013, 11:19
|
Replies: 37
Views: 43,262
Z touch software
If you have any type of Probe software remove it ,along with the wire to your board. I have it it cause a similar problem on my machine.
|
Forum: MechMates already cutting
Thu 08 November 2012, 17:43
|
Replies: 610
Views: 478,286
|
Forum: MechMates already cutting
Sun 04 November 2012, 12:26
|
Replies: 130
Views: 94,903
|
Forum: 10. Base Table
Mon 29 October 2012, 16:22
|
Replies: 3
Views: 11,104
|
Forum: 80. Computer Hardware & Software
Tue 23 October 2012, 17:11
|
Replies: 8
Views: 11,674
Scan
Hi Al, I have a 3D scanner if you would like to make a copy of one of them and send it to me, I could scan it and send you a file to try, Leonard
|
Forum: The Market Place
Wed 18 April 2012, 19:50
|
Replies: 67
Views: 53,744
I have used Master Cam, Art Cam, Aspire and...
I have used Master Cam, Art Cam, Aspire and several others, of them all Bob Cad has to be the worst in all area's of use, not to mention the agravation of them calling you all the time to upgrade,...
|
Forum: Miscellaneous / General / Whatever / Catchall
Sun 25 March 2012, 15:11
|
Replies: 2
Views: 4,504
|
Forum: Graphics & CAD
Fri 09 March 2012, 16:54
|
Replies: 12
Views: 15,853
It is the same in solid works also it will not...
It is the same in solid works also it will not extrude if it is open, you can create relations to all of the slots , where if you change one it will change the rest of them to the same measurement.
|
Forum: Utility software
Thu 07 April 2011, 20:20
|
Replies: 2
Views: 9,606
Inkscape
Also great for cursive writing will jion and trim the letters save as a dxf and cut
|
Forum: Construction started, but not cutting yet
Fri 11 February 2011, 16:05
|
Replies: 85
Views: 102,536
|
Forum: The Market Place
Sat 20 November 2010, 19:53
|
Replies: 0
Views: 4,581
STL Files
Hi guys , I have started making a few 3D drawings and thought I would see if anyone was interested. They are priced fairly cheap. I will be adding new drawings every few months . So take a look if...
|
Forum: MechMates already cutting
Tue 09 February 2010, 18:49
|
Replies: 118
Views: 92,799
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Wed 03 February 2010, 18:05
|
Replies: 449
Views: 471,123
Well,give a little take a little. The hole is...
Well,give a little take a little. The hole is smaller, but a person could turn a spacer and weld it into the original motor mount kind of like chopper did. Then just make the other plate out of flat...
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Wed 03 February 2010, 13:21
|
Replies: 449
Views: 471,123
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Sat 30 January 2010, 20:30
|
Replies: 449
Views: 471,123
The two small washer are what keeps the shaft...
The two small washer are what keeps the shaft from wondering around, they work like a thrust washer and ride against the inner race of the bearing one on each side. I supply it in the kit. But you...
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Sat 30 January 2010, 18:06
|
Replies: 449
Views: 471,123
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Sat 30 January 2010, 17:49
|
Replies: 449
Views: 471,123
|
Forum: MechMates already cutting
Thu 28 January 2010, 06:51
|
Replies: 1,586
Views: 1,022,631
|
Forum: MechMates already cutting
Thu 28 January 2010, 00:16
|
Replies: 1,586
Views: 1,022,631
|
Forum: MechMates already cutting
Thu 28 January 2010, 00:15
|
Replies: 1,586
Views: 1,022,631
|
Forum: MechMates already cutting
Wed 27 January 2010, 23:18
|
Replies: 1,586
Views: 1,022,631
Kobus since you do have a regular motor also ,...
Kobus since you do have a regular motor also , you could turn this. You should by able to change to a side view then draw the profile, you would then select this line as a contour to cut, You can...
|
Forum: MechMates already cutting
Wed 27 January 2010, 20:44
|
Replies: 1,586
Views: 1,022,631
|