Forum: The Market Place
Wed 21 June 2017, 22:51
|
Replies: 7
Views: 22,051
|
Forum: 70. Control Systems
Tue 14 February 2017, 23:06
|
Replies: 5
Views: 18,347
|
Forum: 70. Control Systems
Tue 14 February 2017, 02:41
|
Replies: 5
Views: 18,347
|
Forum: MechMates already cutting
Mon 06 February 2017, 02:31
|
Replies: 454
Views: 436,048
|
Forum: MechMates already cutting
Sat 04 February 2017, 06:13
|
Replies: 454
Views: 436,048
|
Forum: Construction started, but not cutting yet
Mon 28 November 2016, 07:24
|
Replies: 126
Views: 152,219
|
Forum: 80. Computer Hardware & Software
Sun 20 November 2016, 07:41
|
Replies: 1
Views: 10,089
Eding CNC Controller
Hi Folks,
Its been a long time since I have posted anything on this forum, but wanted to share something, Have been using Eding CNC 's ethernet based controller for some time - seen that it works...
|
Forum: MechMates already cutting
Fri 03 July 2015, 05:07
|
Replies: 95
Views: 158,624
|
Forum: MechMates already cutting
Wed 01 July 2015, 04:28
|
Replies: 95
Views: 158,624
|
Forum: MechMates already cutting
Tue 30 June 2015, 00:49
|
Replies: 95
Views: 158,624
|
Forum: 702. Power Supplies
Mon 29 June 2015, 02:31
|
Replies: 134
Views: 156,357
58V DC would be just about fine for the motors...
58V DC would be just about fine for the motors -go ahead - some times we use fans to cool down motors on X and Z - especially when they are working on 3d jobs, else there will be sometime a loss of...
|
Forum: MechMates already cutting
Mon 29 June 2015, 01:53
|
Replies: 95
Views: 158,624
|
Forum: 50. Toolheads
Thu 18 June 2015, 05:07
|
Replies: 3
Views: 11,804
|
Forum: 50. Toolheads
Wed 17 June 2015, 04:48
|
Replies: 3
Views: 11,804
Huajing 3kw aircooled spindles
Hi folks - so finally had to replace bearing on a couple of Huajing spindles - all these Asian spindles are advertised as " Adopt GERMAN BEARING " I got to know what these bearing were - these were...
|
Forum: MechMates already cutting
Fri 27 March 2015, 03:45
|
Replies: 174
Views: 164,382
I always use a 10A fuse before supplying AC to...
I always use a 10A fuse before supplying AC to the transformer, essentially a short on the secondary will instigate a surge on the primary which will cause a short circuit, usually a fuse or a cb...
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Sat 14 February 2015, 02:19
|
Replies: 87
Views: 107,137
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Sun 08 February 2015, 23:52
|
Replies: 87
Views: 107,137
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Fri 06 February 2015, 03:28
|
Replies: 87
Views: 107,137
|
Forum: MechMates already cutting
Sat 20 September 2014, 07:18
|
Replies: 82
Views: 84,388
|
Forum: MechMates already cutting
Thu 15 May 2014, 03:01
|
Replies: 518
Views: 320,910
Check the capacitor of the power supply, try...
Check the capacitor of the power supply, try adding a 1000uF electrolytic cap at the drive end parallel to powersupply - ( see if provides any soln)
I have faced similar situation where it started...
|
Forum: 60. Wiring & Cable Management
Wed 05 February 2014, 08:43
|
Replies: 4
Views: 11,322
The asian air cooled spindle will work good if...
The asian air cooled spindle will work good if you plan to just carve wood and use endmills maybe upto 8mm in diameter, if you are planning to use bigger cutting bits say in the range of 20mm + I...
|
Forum: MechMates already cutting
Mon 24 June 2013, 20:02
|
Replies: 778
Views: 502,913
|
Forum: MechMates already cutting
Wed 08 May 2013, 12:32
|
Replies: 778
Views: 502,913
|
Forum: MechMates already cutting
Tue 07 May 2013, 07:56
|
Replies: 778
Views: 502,913
|