Forum: Troubleshooting
Mon 12 November 2012, 03:49
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Mon 12 November 2012, 03:45
|
Replies: 85
Views: 80,265
Hi Red - Thanks for replying but we have been...
Hi Red - Thanks for replying but we have been using the calibration setting and taking measurements over 980mm with a good quality set of engineering vernier calipers.
I am hoping that having the...
|
Forum: Troubleshooting
Sat 10 November 2012, 10:27
|
Replies: 85
Views: 80,265
Hi Gerald,
I think we'll be...
Hi Gerald,
I think we'll be looking/dismantling the z Slide tomorrow now as we have only just finished getting the racks fixed back on strait this afternoon. They are certainly much better now...
|
Forum: Troubleshooting
Fri 09 November 2012, 10:16
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 08:33
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 07:56
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 06:40
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 06:29
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 06:25
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 06:19
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 06:17
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 06:16
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 05:02
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 09 November 2012, 04:16
|
Replies: 85
Views: 80,265
We'll back to it this morning. Once again thank...
We'll back to it this morning. Once again thank you all for your input and support in trying to get his sorted. It is most definitely driving us up the wall a bit now as its just putting us further...
|
Forum: Troubleshooting
Thu 08 November 2012, 14:24
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Thu 08 November 2012, 10:51
|
Replies: 85
Views: 80,265
Update :mad:
Well time to back track a bit now.
It is not after the last calibration cutting distances accurately.
We thought we had it sorted with the method I described earlier.
We can get it to cut a...
|
Forum: Troubleshooting
Wed 07 November 2012, 04:17
|
Replies: 85
Views: 80,265
Hi there,
Many thank to Chris (cdev) for the...
Hi there,
Many thank to Chris (cdev) for the teflon washers. It has definately improved both rigidity and action of the stepper mounting plates.
Antony were fairly certain were not loosing...
|
Forum: Troubleshooting
Sun 04 November 2012, 09:22
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Sat 03 November 2012, 06:04
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 02 November 2012, 12:03
|
Replies: 85
Views: 80,265
The rails and rack do slide smoothly and the...
The rails and rack do slide smoothly and the pinion seems well seated.
We have just added some more tension to all of the springs for good measure.
Does any body know where we can purchase teflon...
|
Forum: Troubleshooting
Fri 02 November 2012, 09:36
|
Replies: 85
Views: 80,265
Hi Ross,
We had already tightened the...
Hi Ross,
We had already tightened the springs (Drilled new bolt holes for the bolts they attach to) and the pinions do seem well engaged with the rack and the Roller bearing seems quite firmly...
|
Forum: Troubleshooting
Fri 02 November 2012, 08:45
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Fri 02 November 2012, 07:35
|
Replies: 85
Views: 80,265
Right, Well. We have straitened the y rails and...
Right, Well. We have straitened the y rails and have the y car sitting much more firmly on them. This has improved the cuts some what but we are still seeing an issue as the cutter enters and exits...
|
Forum: Troubleshooting
Wed 31 October 2012, 06:31
|
Replies: 85
Views: 80,265
|
Forum: Troubleshooting
Wed 31 October 2012, 06:28
|
Replies: 85
Views: 80,265
HRoss,
I think your post came in just as I...
HRoss,
I think your post came in just as I was writing that one. Its such a shame as we bought this one thinking it would be a quicker route than either getting a chinese machine or building our...
|