Forum: MechMates already cutting
Tue 06 March 2012, 13:00
|
Replies: 109
Views: 149,532
|
Forum: MechMates already cutting
Sun 25 December 2011, 22:34
|
Replies: 128
Views: 209,922
|
Forum: Construction started, but not cutting yet
Tue 04 October 2011, 09:29
|
Replies: 3
Views: 7,039
|
Forum: MechMates already cutting
Sun 20 February 2011, 09:44
|
Replies: 1,078
Views: 1,399,362
Hi All
Tought this was allready posted...
Hi All
Tought this was allready posted before, but this is the way Chinese manufacturers get there Germany bearings
http://www.tradett.com/germany-bearing-products/
|
Forum: MechMates already cutting
Fri 04 February 2011, 17:07
|
Replies: 202
Views: 323,895
|
Forum: 10. Base Table
Mon 27 December 2010, 05:02
|
Replies: 20
Views: 29,470
Yes this will work accurate enough. If you use...
Yes this will work accurate enough. If you use water, add to drops of Dreft or alike, to lower the surface tension of the water. This way the surface will be flat and your readings accurate.
My 2...
|
Forum: MechMates already cutting
Tue 30 November 2010, 09:35
|
Replies: 1,078
Views: 1,399,362
|
Forum: 60. Wiring & Cable Management
Sun 21 November 2010, 09:17
|
Replies: 73
Views: 110,868
|
Forum: 60. Wiring & Cable Management
Tue 26 October 2010, 12:50
|
Replies: 3
Views: 11,303
Francis,
Brad covered the electrical issues....
Francis,
Brad covered the electrical issues. There's also a mechanical issue. Twisted pair is a solid core wire and that's a problem being continually bended in the e-chain. Broken cables is...
|
Forum: Rails & Rollers
Sun 08 August 2010, 05:22
|
Replies: 7
Views: 12,321
|
Forum: Rails & Rollers
Sat 07 August 2010, 10:23
|
Replies: 7
Views: 12,321
|
Forum: 60. Wiring & Cable Management
Tue 20 July 2010, 21:43
|
Replies: 221
Views: 224,011
|
Forum: Rails & Rollers
Wed 26 May 2010, 08:37
|
Replies: 3
Views: 10,622
Tom,
Then have a look at drawing M 10 120....
Tom,
Then have a look at drawing M 10 120. Specialy the remark that you have to make a fillet radius etc.
You can still use youre angle iron. 40 becomes 16 mm measured from the inside. That will...
|
Forum: Rails & Rollers
Wed 26 May 2010, 05:36
|
Replies: 3
Views: 10,622
Tom
Look at drawing M1 10 110, there you'll...
Tom
Look at drawing M1 10 110, there you'll see that the final height of the rails will be 28 mm. So first you have to grind the rail down to 28 mm, then you must grind the 45 degree angles.
...
|
Forum: Introduce yourself and start planning
Wed 12 May 2010, 16:07
|
Replies: 19
Views: 12,548
|
Forum: MechMates already cutting
Wed 10 February 2010, 00:50
|
Replies: 36
Views: 26,913
|
Forum: MechMates already cutting
Thu 28 January 2010, 16:25
|
Replies: 118
Views: 93,034
|
Forum: Troubleshooting
Tue 12 January 2010, 10:01
|
Replies: 25
Views: 20,470
Irfan
Although still in lurking phase and...
Irfan
Although still in lurking phase and planning the build, is this treath maybe of any help for your problem?
http://www.mechmate.com/forums/showthread.php?t=1019
Just trying to help -...
|
Forum: About this Forum
Sun 03 January 2010, 05:38
|
Replies: 25
Views: 35,775
|
Forum: Cutting various materials - bit selection, feeds, speeds
Mon 07 December 2009, 16:25
|
Replies: 25
Views: 39,289
|
Forum: Introduce yourself and start planning
Thu 03 December 2009, 15:10
|
Replies: 14
Views: 15,571
|
Forum: Profiled (laser cut) & bent steel plate
Wed 11 November 2009, 01:37
|
Replies: 33
Views: 57,268
|
Forum: Construction started, but not cutting yet
Sun 11 October 2009, 02:19
|
Replies: 121
Views: 162,752
|
Forum: About this Forum
Sun 04 October 2009, 01:12
|
Replies: 47
Views: 51,903
|
Forum: Utility software
Sat 05 September 2009, 03:14
|
Replies: 5
Views: 20,192
Hallo Alan,
Though a little bit late, just...
Hallo Alan,
Though a little bit late, just stepped into this threath, I us PDFILL. Not only merge pdf files but it will do a lot more and it's free trail and 19.99 for keeps. You can download it...
|