Forum: MechMates already cutting
Fri 26 October 2018, 21:42
|
Replies: 197
Views: 279,618
|
Forum: MechMates already cutting
Sun 19 June 2016, 11:32
|
Replies: 100
Views: 237,888
|
Forum: MechMates already cutting
Tue 10 May 2016, 15:25
|
Replies: 100
Views: 237,888
|
Forum: MechMates already cutting
Sun 24 April 2016, 19:07
|
Replies: 414
Views: 228,789
|
Forum: MechMates already cutting
Tue 19 April 2016, 15:12
|
Replies: 414
Views: 228,789
|
Forum: MechMates already cutting
Sun 17 April 2016, 10:52
|
Replies: 518
Views: 324,594
I have the entry level GoPro Hero+. Its the one...
I have the entry level GoPro Hero+. Its the one with wifi so I can sit on the couch and see whats going on in the garage. Knowing what I know now I would have asked for the Hero 3 or 4. Its alot of...
|
Forum: MechMates already cutting
Sat 16 April 2016, 20:09
|
Replies: 518
Views: 324,594
Here is a Time Lapse of my machine cutting out...
Here is a Time Lapse of my machine cutting out some plaques for the guys at work. I used a 1/8th endmill and a 30 degree Vbit. Machine was actually running at 100 ipm and the run time was around 3...
|
Forum: Construction started, but not cutting yet
Tue 29 March 2016, 19:07
|
Replies: 85
Views: 109,194
|
Forum: General - MM Build
Sun 19 July 2015, 20:20
|
Replies: 258
Views: 409,561
|
Forum: MechMates already cutting
Mon 15 June 2015, 11:31
|
Replies: 735
Views: 490,793
|
Forum: MechMates already cutting
Wed 10 June 2015, 07:43
|
Replies: 735
Views: 490,793
I hooked up the Estop but start and pause are...
I hooked up the Estop but start and pause are not. Most of the time I zero with the phone and hit start from it. In a production environment where you cut the same sheet all day long and paying...
|
Forum: MechMates already cutting
Wed 10 June 2015, 05:52
|
Replies: 735
Views: 490,793
|
Forum: MechMates already cutting
Tue 09 June 2015, 20:18
|
Replies: 735
Views: 490,793
I am not a Mach user but in Linuxcnc you can...
I am not a Mach user but in Linuxcnc you can switch between commanded and actual. Seeing the difference would drive me nuts. Prime example of driving me nuts would be this guys Dro. Cool project but...
|
Forum: MechMates already cutting
Sat 16 May 2015, 11:14
|
Replies: 23
Views: 28,988
V wheels are free from compacted dust? Also...
V wheels are free from compacted dust? Also adding direction of the axis in the photos will help further with which axis is causing the trouble. Have you tried different speeds? Make a series of...
|
Forum: Troubleshooting
Fri 15 May 2015, 20:28
|
Replies: 49
Views: 64,882
|
Forum: MechMates already cutting
Mon 26 January 2015, 23:28
|
Replies: 479
Views: 548,942
Have a look at your nodes in the part file. See...
Have a look at your nodes in the part file. See if the scallops somewhat represent what the nodes look like. Also try on a scrap piece a manual cut that goes diagonally. IE G1 x0y0, x45y45. See if...
|
Forum: MechMates already cutting
Fri 02 January 2015, 13:52
|
Replies: 414
Views: 228,789
I also say dont give up. I have cut .032, .041,...
I also say dont give up. I have cut .032, .041, .020 with no problems also with a 1/8th O-flute. The aluminum I usually use comes with a protective covering on it that I spray adhesive down to a 3/4...
|
Forum: MechMates already cutting
Sat 01 November 2014, 23:47
|
Replies: 518
Views: 324,594
|
Forum: MechMates already cutting
Sat 01 November 2014, 09:54
|
Replies: 518
Views: 324,594
Fox, there is a 1/4 of the socket sticking up...
Fox, there is a 1/4 of the socket sticking up from the top of the holder. I don't think it would be hard but then again I have a don't work with grease on my hands. Most of the time I have gloves on...
|
Forum: MechMates already cutting
Fri 31 October 2014, 21:40
|
Replies: 518
Views: 324,594
|
Forum: MechMates already cutting
Mon 27 October 2014, 10:17
|
Replies: 984
Views: 686,184
|
Forum: MechMates already cutting
Mon 27 October 2014, 01:10
|
Replies: 984
Views: 686,184
|
Forum: MechMates already cutting
Sat 25 October 2014, 22:56
|
Replies: 984
Views: 686,184
|
Forum: MechMates already cutting
Sat 25 October 2014, 18:21
|
Replies: 518
Views: 324,594
|
Forum: MechMates already cutting
Tue 21 October 2014, 21:48
|
Replies: 518
Views: 324,594
Thanks guys,
Yes they are the Ron Paulk...
Thanks guys,
Yes they are the Ron Paulk work benches. I bought his plans awhile ago before all the new tables he has designed. I have to say it was a well need and great addition to the garage....
|