Forum: MechMates already cutting
Sat 29 May 2021, 05:58
|
Replies: 117
Views: 135,663
|
Forum: MechMates already cutting
Fri 28 May 2021, 05:16
|
Replies: 117
Views: 135,663
|
Forum: MechMates already cutting
Fri 28 May 2021, 04:46
|
Replies: 117
Views: 135,663
Been a while, Mechmate #100 has been whirring...
Been a while, Mechmate #100 has been whirring away quietly doing all sorts of odd jobs. In the last couple of years it has moved the Clare Valley in South Australia and lives a quieter life in...
|
Forum: MechMates already cutting
Sun 11 February 2018, 20:35
|
Replies: 440
Views: 834,923
|
Forum: MechMates already cutting
Wed 23 December 2015, 03:26
|
Replies: 117
Views: 135,663
Vacuum clamp
From the inspiration of Deere #116 a mini vacuum table. Needed to make something quick to hold some wooden boards in place for cutting into cheese boards. 200 x 200 mm and worked a treat.
|
Forum: MechMates already cutting
Thu 12 November 2015, 17:17
|
Replies: 216
Views: 214,833
|
Forum: Introduce yourself and start planning
Wed 11 November 2015, 21:22
|
Replies: 21
Views: 23,939
|
Forum: Introduce yourself and start planning
Wed 04 November 2015, 03:14
|
Replies: 21
Views: 23,939
|
Forum: Introduce yourself and start planning
Wed 04 November 2015, 03:09
|
Replies: 21
Views: 23,939
|
Forum: MechMates already cutting
Mon 02 November 2015, 16:04
|
Replies: 216
Views: 214,833
|
Forum: MechMates already cutting
Thu 29 October 2015, 20:21
|
Replies: 216
Views: 214,833
|
Forum: MechMates already cutting
Thu 29 October 2015, 19:57
|
Replies: 216
Views: 214,833
|
Forum: MechMates already cutting
Thu 29 October 2015, 19:36
|
Replies: 735
Views: 481,749
|
Forum: MechMates already cutting
Mon 14 September 2015, 06:39
|
Replies: 202
Views: 322,838
I run a 10mm compression bit and cut my carcase...
I run a 10mm compression bit and cut my carcase material 16mm melamine on particle board, run the spindle at 12000rpm and feed rate at 5m/min. I find as long as scale the spindle rpm down to match...
|
Forum: MechMates already cutting
Wed 03 June 2015, 00:29
|
Replies: 1,078
Views: 1,397,366
I use a 2.4mm straight cut, you get pretty good...
I use a 2.4mm straight cut, you get pretty good finish with a quick sand any swarf is gone. I cut shapes for a craft person do up to 300 at a time, while a sheet is cutting I'm cleaning the previous...
|
Forum: MechMates already cutting
Sat 30 May 2015, 01:31
|
Replies: 735
Views: 481,749
|
Forum: MechMates already cutting
Sun 24 May 2015, 22:46
|
Replies: 1,078
Views: 1,397,366
Elongated holes
Pretty sure we used a die grinder bit, $25 to $30 for a air die grinder Supercheap or Bunnings and around $20 for a bit.
|
Forum: MechMates already cutting
Fri 28 November 2014, 05:23
|
Replies: 735
Views: 481,749
That's the same motors I run. Difference is I'm...
That's the same motors I run. Difference is I'm running Gecko drives, until we installed the 4:1 drive reduction I had issues with the z axis pulling into the job sometimes with upcut bits. I also...
|
Forum: MechMates already cutting
Thu 06 November 2014, 20:14
|
Replies: 735
Views: 481,749
|
Forum: MechMates already cutting
Sun 02 November 2014, 04:29
|
Replies: 735
Views: 481,749
|
Forum: MechMates already cutting
Thu 30 October 2014, 04:52
|
Replies: 735
Views: 481,749
|
Forum: MechMates already cutting
Thu 30 October 2014, 02:02
|
Replies: 735
Views: 481,749
|
Forum: MechMates already cutting
Thu 30 October 2014, 01:46
|
Replies: 735
Views: 481,749
|
Forum: MechMates already cutting
Thu 30 October 2014, 00:33
|
Replies: 735
Views: 481,749
|
Forum: MechMates already cutting
Thu 30 October 2014, 00:29
|
Replies: 735
Views: 481,749
|