Forum: Construction started, but not cutting yet
Wed 07 April 2010, 20:02
|
Replies: 19
Views: 21,423
|
Forum: 702. Power Supplies
Tue 30 March 2010, 17:11
|
Replies: 28
Views: 51,722
|
Forum: 702. Power Supplies
Tue 30 March 2010, 16:09
|
Replies: 28
Views: 51,722
|
Forum: 702. Power Supplies
Mon 29 March 2010, 18:15
|
Replies: 28
Views: 51,722
Hello, I have this and been messing around with...
Hello, I have this and been messing around with it, looks like I will be able to get the voltage I need but how does one tell if it will have enough current /amps that I will need, would like to know...
|
Forum: Construction started, but not cutting yet
Fri 19 March 2010, 10:49
|
Replies: 19
Views: 21,423
|
Forum: Construction started, but not cutting yet
Thu 18 March 2010, 16:28
|
Replies: 19
Views: 21,423
|
Forum: Construction started, but not cutting yet
Wed 17 March 2010, 20:44
|
Replies: 19
Views: 21,423
Z-plate finished ,milwaukee bracket made
haven't had a lot of time to work on mm lately, which is a good thing, work seems to be picking back up, got the reduction boxes finished, z plate ground and tapped and destroyed a good router base...
|
Forum: Construction started, but not cutting yet
Sun 28 February 2010, 22:19
|
Replies: 19
Views: 21,423
she's up and rolling, got the rails ground, it...
she's up and rolling, got the rails ground, it wasn't as bad as I thought it was going to be, with a good disk for cutting and a good mind set it went pretty well, with grinding the v, I used a 36...
|
Forum: Motors & their mountings
Sun 21 February 2010, 17:29
|
Replies: 56
Views: 76,299
|
Forum: Motors & their mountings
Sun 21 February 2010, 14:43
|
Replies: 56
Views: 76,299
thanks mike, buy looking at the specs can you...
thanks mike, buy looking at the specs can you tell me the mh,if wired bipolar parallel? I am assuming it can be with 8 leads or am I wrong in thinking this? by looking at there recommended drivers to...
|
Forum: Motors & their mountings
Sun 21 February 2010, 11:54
|
Replies: 56
Views: 76,299
Mike ,would you care to take a look at these...
Mike ,would you care to take a look at these specs and give you thoughts, http://www.circuitspecialists.com/products/pdf/85BYGH450B-03.pdf ,this is a 8 wire motor, I believe, and if the spec are in...
|
Forum: Motors & their mountings
Sun 21 February 2010, 09:24
|
Replies: 56
Views: 76,299
|
Forum: Motors & their mountings
Sun 21 February 2010, 09:19
|
Replies: 56
Views: 76,299
thanks Mike, for your time and effort, they do...
thanks Mike, for your time and effort, they do have those in stock, I am wanting something in the 600 oz range with the eight wire option, like KL34H280-45-8A , which is being advertised in stock,...
|
Forum: Motors & their mountings
Sat 20 February 2010, 23:26
|
Replies: 56
Views: 76,299
hello, been looking for motors, keling willl be...
hello, been looking for motors, keling willl be 60 days, came across these, http://www.circuitspecialists.com/prod.itml/icOid/8930 and was wondering if anyone has any experience or opinion on these...
|
Forum: Construction started, but not cutting yet
Mon 15 February 2010, 20:35
|
Replies: 19
Views: 21,423
thanks guys for the welcome,and thank you John...
thanks guys for the welcome,and thank you John for the heads up on the dewalt disk, made a world of difference, cut the other y rail and wore down a little over 1/8 ",I'll be glad when these are...
|
Forum: Construction started, but not cutting yet
Sun 14 February 2010, 19:40
|
Replies: 19
Views: 21,423
Up and Rolling - Johnson City,TN
Hello Everyone, this is my first post as a builder,been reading and looking over the plans for a while, I have been off work for a week and thought it would be a good time to dive in and get started....
|
Forum: General - MM Build
Fri 15 January 2010, 15:49
|
Replies: 6
Views: 10,022
Thanks everyone for your reply, It was just a...
Thanks everyone for your reply, It was just a thought, wasnt trying to change the great design Gearld has, it was what we use alot of at work and have access to. Went ahead ordered the parts in steel...
|
Forum: General - MM Build
Wed 06 January 2010, 16:27
|
Replies: 6
Views: 10,022
mm parts made of aluminum?
Hello, I am new here and very interested in building the mechmate. could the metal parts that are bent be made from aluminum?, we have two cnc routers at work that could cut these parts. dont have...
|