Forum: Introduce yourself and start planning
Sat 09 July 2022, 15:12
|
Replies: 5
Views: 5,297
|
Forum: Miscellaneous / General / Whatever / Catchall
Wed 29 July 2020, 14:24
|
Replies: 2
Views: 12,332
I installed couple of fiber laser systems, not...
I installed couple of fiber laser systems, not knowing what have you seen the head is least of expense, the source and fiber with connector to the head is much more. Also Head can be with autofocus...
|
Forum: Introduce yourself and start planning
Mon 17 February 2020, 15:09
|
Replies: 6
Views: 10,814
|
Forum: Introduce yourself and start planning
Sat 15 February 2020, 19:14
|
Replies: 6
Views: 10,814
These I use for almost all machines now ,...
These I use for almost all machines now , affordable and powerful
https://vallder.com/en/c/292/38/stepper-motor-drivers/closed-loop-stepper-8-5nm-detail
...but looking at the stepperonline...
|
Forum: CNC motion control software
Sun 02 June 2019, 02:26
|
Replies: 3
Views: 20,648
|
Forum: MechMates already cutting
Thu 23 May 2019, 15:19
|
Replies: 56
Views: 86,847
|
Forum: 701. Motor Drives
Sat 23 March 2019, 04:51
|
Replies: 2
Views: 26,059
What breakout board are you using ? is it...
What breakout board are you using ? is it optoisolated?
If it is isolated I would first try to connect the PC to the mains with small line filter.
also check if everything is properly grounded...
|
Forum: 701. Motor Drives
Mon 28 January 2019, 14:18
|
Replies: 1
Views: 7,346
|
Forum: Introduce yourself and start planning
Sat 05 January 2019, 15:01
|
Replies: 1
Views: 8,554
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Fri 04 January 2019, 05:57
|
Replies: 449
Views: 477,964
|
Forum: Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Mon 31 December 2018, 04:58
|
Replies: 449
Views: 477,964
|
Forum: Introduce yourself and start planning
Sun 05 August 2018, 06:11
|
Replies: 15
Views: 20,538
|
Forum: Graphics & CAD
Fri 03 August 2018, 15:10
|
Replies: 5
Views: 12,946
|
Forum: Construction started, but not cutting yet
Tue 01 May 2018, 18:53
|
Replies: 42
Views: 57,302
|
Forum: Construction started, but not cutting yet
Sat 28 April 2018, 13:44
|
Replies: 42
Views: 57,302
You dont have to optioisolate step/dir outputs...
You dont have to optioisolate step/dir outputs because there are optocouplers inside stepper drives , best cheap board is the one with one relay, 0-10v analog spindle rpm output, 12-24Vdc supply and...
|
Forum: MechMates already cutting
Wed 21 March 2018, 19:43
|
Replies: 694
Views: 383,388
|
Forum: Motors & their mountings
Sun 11 March 2018, 06:18
|
Replies: 8
Views: 16,818
|
Forum: Motors & their mountings
Fri 09 March 2018, 14:58
|
Replies: 8
Views: 16,818
|
Forum: Motors & their mountings
Tue 06 March 2018, 20:29
|
Replies: 8
Views: 16,818
80V might be too much , its also limit for most...
80V might be too much , its also limit for most drives so you should keep it a bit lower. Using 65V I got all the performance needed and you can also confirm in couple of topics here on forum that...
|
Forum: Motors & their mountings
Sun 04 March 2018, 16:05
|
Replies: 8
Views: 16,818
|
Forum: MechMates already cutting
Tue 13 February 2018, 10:29
|
Replies: 479
Views: 537,688
Robert all these VFDs are 3 phase 230V input ,...
Robert all these VFDs are 3 phase 230V input , since this is only usable in Japan :) we all connect it single phase 230 , so at L1 you wire your LIVE and at L3 you wire NEUTRAL and thats it
in...
|
Forum: MechMates already cutting
Fri 26 January 2018, 10:01
|
Replies: 479
Views: 537,688
I was working nearby two of chinese "HSD" 6kw...
I was working nearby two of chinese "HSD" 6kw spindles , and its not a pleasant experience, the fans were mounted on shaft, at 15k RPM its deafening . Original HSD motors with ATC are a different...
|
Forum: MechMates already cutting
Wed 24 January 2018, 13:23
|
Replies: 479
Views: 537,688
|
Forum: MechMates already cutting
Mon 22 January 2018, 15:30
|
Replies: 479
Views: 537,688
|
Forum: MechMates already cutting
Mon 22 January 2018, 07:57
|
Replies: 479
Views: 537,688
|