Forum: MechMates already cutting
Wed 28 April 2010, 19:15
|
Replies: 1,586
Views: 1,028,124
|
Forum: Troubleshooting
Fri 09 April 2010, 21:38
|
Replies: 28
Views: 28,360
|
Forum: MechMates already cutting
Fri 09 April 2010, 21:38
|
Replies: 518
Views: 323,139
|
Forum: Troubleshooting
Fri 09 April 2010, 21:26
|
Replies: 28
Views: 28,360
|
Forum: MechMates already cutting
Fri 09 April 2010, 21:26
|
Replies: 518
Views: 323,139
|
Forum: Troubleshooting
Fri 09 April 2010, 21:20
|
Replies: 28
Views: 28,360
|
Forum: MechMates already cutting
Fri 09 April 2010, 21:20
|
Replies: 518
Views: 323,139
|
Forum: MechMates already cutting
Fri 09 April 2010, 20:54
|
Replies: 518
Views: 323,139
|
Forum: Troubleshooting
Fri 09 April 2010, 20:54
|
Replies: 28
Views: 28,360
|
Forum: Troubleshooting
Fri 09 April 2010, 20:29
|
Replies: 28
Views: 28,360
Russel,
check the coil voltage at A1 A2 In...
Russel,
check the coil voltage at A1 A2 In both senerios---Power on and no green btn.
Power on green btn. manually held.I agree it sounds like your relay is missing proper
feed to latch.
|
Forum: MechMates already cutting
Fri 09 April 2010, 20:29
|
Replies: 518
Views: 323,139
Russel,
check the coil voltage at A1 A2 In...
Russel,
check the coil voltage at A1 A2 In both senerios---Power on and no green btn.
Power on green btn. manually held.I agree it sounds like your relay is missing proper
feed to latch.
|
Forum: MechMates already cutting
Fri 09 April 2010, 18:53
|
Replies: 479
Views: 541,793
Robert,you slipped by me.5 star fit and...
Robert,you slipped by me.5 star fit and finish.Your choice of steel schedule,top notch.
Your ability to slide this by the wife on the living room floor= priceless $$$.Honestly
great fabrication.
|
Forum: 10. Base Table
Thu 08 April 2010, 21:40
|
Replies: 84
Views: 105,439
|
Forum: 10. Base Table
Wed 07 April 2010, 21:49
|
Replies: 84
Views: 105,439
Dave good job,
Yes , this is very similar to...
Dave good job,
Yes , this is very similar to what I was trying to describe.A modified thought was rather than leaving the tops of the vertical rails floating,bolt it on to a adjustable
bracket for...
|
Forum: 10. Base Table
Tue 06 April 2010, 20:16
|
Replies: 84
Views: 105,439
|
Forum: 10. Base Table
Tue 06 April 2010, 20:11
|
Replies: 84
Views: 105,439
Dave,
Greg's pictures are exactly what I'm...
Dave,
Greg's pictures are exactly what I'm suggesting.The table itself,A simple flat platform,that goes up and down.The foundation that I'm referring to is also just like Greg's,note the stiff box...
|
Forum: 10. Base Table
Mon 05 April 2010, 21:58
|
Replies: 84
Views: 105,439
Dave,
Go back to your 1st design,look at the...
Dave,
Go back to your 1st design,look at the difference in weight on the moving table.The last design is not only overly designed, but puts all that weight in the worst possible place on the...
|
Forum: 10. Base Table
Sat 03 April 2010, 13:55
|
Replies: 84
Views: 105,439
Dave,
Go to ebay site,search( thk linear) look...
Dave,
Go to ebay site,search( thk linear) look for shs or hsr style rails and blocks. 25mm
to large 15mm to small 20mm just right according to the three little bears.The lift you have pictured...
|
Forum: 10. Base Table
Sat 03 April 2010, 11:32
|
Replies: 84
Views: 105,439
Dave,
on the scissor jack,I have one on my late...
Dave,
on the scissor jack,I have one on my late model GMC truck.It has plenty of stroke,payload not much issue. It also has 90 degree strait up throw(neutral).It can be used with an impact.At a junk...
|
Forum: 10. Base Table
Sat 03 April 2010, 10:03
|
Replies: 84
Views: 105,439
Hi Dave,
Interesting design,using four screw...
Hi Dave,
Interesting design,using four screw jacks to lift the table with an adaptable impact wrench,would be easy but you could end up racking the table as well.Turning the
screws by ratchet,well...
|
Forum: General - MM Operating
Sun 28 March 2010, 14:12
|
Replies: 20
Views: 28,861
|
Forum: General - MM Operating
Sun 28 March 2010, 10:57
|
Replies: 20
Views: 28,861
Robert,
I'm using Onsrud 2.5"insert straight...
Robert,
I'm using Onsrud 2.5"insert straight cutter ,part 91-102 .feed speed f-200 to f-600
@12000-16000 rpm.This bit is rated to 18000 max.As advertised no mill marks,it looks and feels as it...
|
Forum: MechMates already cutting
Mon 22 March 2010, 19:28
|
Replies: 518
Views: 323,139
|
Forum: MechMates already cutting
Mon 22 March 2010, 09:17
|
Replies: 457
Views: 239,054
Ken,
I did not notice the rail key-ways in...
Ken,
I did not notice the rail key-ways in post#240.Your rail numbers are excellent.I like to have the blocks also key -wayed,for the purpose of screw securing,or help keeping them tight.I too had...
|
Forum: MechMates already cutting
Sun 21 March 2010, 13:10
|
Replies: 457
Views: 239,054
|