Forum: MechMates already cutting
Tue 01 June 2021, 12:45
|
Replies: 17
Views: 18,233
Hey Rik#92, on mine, the lead screw is 1/2"...
Hey Rik#92, on mine, the lead screw is 1/2" 10TPI, I think 2 starts. What is the screw you're using in your setup? It looks from your pictures like the gear is mounted on a 1/4" shaft, is that...
|
Forum: MechMates already cutting
Wed 26 May 2021, 11:27
|
Replies: 17
Views: 18,233
|
Forum: MechMates already cutting
Wed 26 May 2021, 10:17
|
Replies: 17
Views: 18,233
|
Forum: MechMates already cutting
Thu 11 March 2021, 12:09
|
Replies: 17
Views: 18,233
|
Forum: MechMates already cutting
Wed 10 March 2021, 07:49
|
Replies: 17
Views: 18,233
|
Forum: 701. Motor Drives
Mon 21 January 2019, 16:52
|
Replies: 1
Views: 7,738
|
Forum: Troubleshooting
Thu 10 January 2019, 07:28
|
Replies: 4
Views: 9,611
I figured out the limit switch settings that...
I figured out the limit switch settings that remove the error, but it seems I'm only getting about 5v from my gecko power supply, so I'm gonna start with replacing that. I visually checked all the...
|
Forum: Troubleshooting
Wed 09 January 2019, 15:37
|
Replies: 4
Views: 9,611
|
Forum: Troubleshooting
Wed 09 January 2019, 13:10
|
Replies: 4
Views: 9,611
|
Forum: Troubleshooting
Wed 09 January 2019, 12:53
|
Replies: 4
Views: 9,611
|
Forum: About this Forum
Thu 27 December 2018, 08:51
|
Replies: 21
Views: 66,358
|
Forum: 50. Toolheads
Wed 26 December 2018, 13:09
|
Replies: 4
Views: 13,457
|
Forum: About this Forum
Wed 26 December 2018, 12:44
|
Replies: 21
Views: 66,358
Brad #10 again, thanks. This error actually...
Brad #10 again, thanks. This error actually hasn't gone completely away. It seems to only skip the gear towards the upper couple inches of travel. I don't know if the speed is still an issue, it...
|
Forum: 701. Motor Drives
Wed 26 December 2018, 10:26
|
Replies: 5
Views: 12,593
Brad #10, thanks for being the most likely to...
Brad #10, thanks for being the most likely to reply to my wacky and imcomplete questions, I'm gonna reply to all your suggestions now. We are using a Huangyang VFD with a 2.2kw water cooled spindle....
|
Forum: 701. Motor Drives
Thu 20 December 2018, 15:23
|
Replies: 5
Views: 12,593
|
Forum: About this Forum
Wed 14 November 2018, 15:55
|
Replies: 21
Views: 66,358
|
Forum: About this Forum
Tue 13 November 2018, 17:27
|
Replies: 21
Views: 66,358
|
Forum: About this Forum
Tue 13 November 2018, 08:43
|
Replies: 21
Views: 66,358
|
Forum: 50. Toolheads
Thu 01 November 2018, 08:51
|
Replies: 4
Views: 13,457
Power to the wall question about Huangyang RFD
Hello, basic question but just trying to be sure I'm barking up the right tree. We are installing a 2.2kw spindle with the Huangyang VFD, and I am almost there on parts but want to make sure I am...
|
Forum: About this Forum
Tue 30 October 2018, 13:05
|
Replies: 21
Views: 66,358
Thanks guys, it's not solved yet but we are...
Thanks guys, it's not solved yet but we are replacing the spindle so I can't play with it at the moment. I have a feeling the gas spring may have been the culprit, it was mounted correctly and is...
|
Forum: 701. Motor Drives
Mon 29 October 2018, 16:06
|
Replies: 20
Views: 45,940
|
Forum: About this Forum
Wed 24 October 2018, 16:40
|
Replies: 21
Views: 66,358
|
Forum: About this Forum
Wed 24 October 2018, 08:52
|
Replies: 21
Views: 66,358
|
Forum: About this Forum
Wed 24 October 2018, 08:08
|
Replies: 21
Views: 66,358
|