MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 7 of 7
Search took
0.00
seconds.
Search:
Posts Made By:
bradm
Forum:
MechMates already cutting
Thu 08 March 2012, 08:48
Replies:
189
Cold Air Gun Success #94 - Northern NJ USA
Views:
248,760
Posted By
bradm
Take off the input manifold and use a reducer...
Take off the input manifold and use a reducer from the big circular opening. Or better, reconstruct the dust collector with a phil thein separator - which you can cut on your mechmate.
Forum:
MechMates already cutting
Mon 20 February 2012, 10:09
Replies:
189
Cold Air Gun Success #94 - Northern NJ USA
Views:
248,760
Posted By
bradm
Ah, that all sounds correct then. "208/120v" is...
Ah, that all sounds correct then. "208/120v" is the common description of that 3 phase service in the US, and the black/red/blue is also standard. "120/240 or 110/220" describes a single phase, and...
Forum:
MechMates already cutting
Sun 19 February 2012, 18:31
Replies:
189
Cold Air Gun Success #94 - Northern NJ USA
Views:
248,760
Posted By
bradm
The wire AWG is chosen for the maximum amperage...
The wire AWG is chosen for the maximum amperage that might come from the source. Since the breakers might feed you up to 20A continuously, and the wire might be buried in a wall where heating would...
Forum:
MechMates already cutting
Sun 19 February 2012, 18:29
Replies:
189
Cold Air Gun Success #94 - Northern NJ USA
Views:
248,760
Posted By
bradm
Oh oh -> Miguel, do you actually have 3 phase...
Oh oh -> Miguel, do you actually have 3 phase service? Most residences have single phase service; if the voltage between two hot legs is twice that between a leg and a neutral, you have single phase...
Forum:
MechMates already cutting
Sun 19 February 2012, 18:15
Replies:
189
Cold Air Gun Success #94 - Northern NJ USA
Views:
248,760
Posted By
bradm
Sorry to hear about your dead VFD. In order to...
Sorry to hear about your dead VFD. In order to select the wire gauge, we should translate the HP or KW values into amperage, and then choose the wire gauge to carry that amperage without undue...
Forum:
MechMates already cutting
Tue 24 January 2012, 13:51
Replies:
189
Cold Air Gun Success #94 - Northern NJ USA
Views:
248,760
Posted By
bradm
You could do either, although my preference would...
You could do either, although my preference would be to use the 4 conductor wire, since it should be less expensive, and requires fewer total connections.
Forum:
MechMates already cutting
Sat 24 September 2011, 20:16
Replies:
189
Cold Air Gun Success #94 - Northern NJ USA
Views:
248,760
Posted By
bradm
Miguel, you make the rails perfectly square to...
Miguel, you make the rails perfectly square to each other so that the gantry rolls true. That means that relative to the table, there will be 1/16" variation, either at one end, or splitting the...
Showing results 1 to 7 of 7
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
00:45
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.