Forum: MechMates already cutting
Wed 02 October 2019, 14:52
|
Replies: 231
Views: 231,784
up and running once again......
After what seems like forever ….. had a computer crash ...then trying to replace the computer with xp os ….then trying to get my mach3 again and set up. Its been fun.
I wore out the bearings on...
|
Forum: MechMates already cutting
Sat 25 March 2017, 13:00
|
Replies: 231
Views: 231,784
Hi Robert, were all doing good over here. Hope...
Hi Robert, were all doing good over here. Hope your doing well also? Yes I had a computer setback. I think the lightning won. It's up and running now. The only thing I have not set back the way it...
|
Forum: MechMates already cutting
Thu 16 March 2017, 10:19
|
Replies: 231
Views: 231,784
So i had posted in the motion control software...
So i had posted in the motion control software thread about this but thought it may be faster to post it here.
My computer crashed and it was unfix able so i have a new windows xp computer up and...
|
Forum: MechMates already cutting
Tue 09 September 2008, 16:58
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Tue 09 September 2008, 16:06
|
Replies: 231
Views: 231,784
Did you mean the one the guy on youtube was...
Did you mean the one the guy on youtube was flying? I haven't found a pattern for that peticular plane but the website up above has some just as good in pdf format. I am not sure exactly how to get...
|
Forum: MechMates already cutting
Tue 09 September 2008, 13:49
|
Replies: 231
Views: 231,784
I like the way they fly very much. There is no...
I like the way they fly very much. There is no airfoil so your flying off the prop all the time. I have only been doing is for about 6 months now. Getting alot better at it though. This guy here is...
|
Forum: MechMates already cutting
Tue 09 September 2008, 08:31
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Mon 08 September 2008, 11:53
|
Replies: 231
Views: 231,784
I don't have a scanner, I am not sure how you...
I don't have a scanner, I am not sure how you would do it with a scanner unless you did sections and then later joined them together on the computer. I started out just googling a search for rc...
|
Forum: MechMates already cutting
Mon 08 September 2008, 08:33
|
Replies: 231
Views: 231,784
Foam cutting
I finally got the foam cutting working good. I am still looking for info on the EPP foam cutting but someone told me a tile grout bit works best on the EPP, so when I have time I will try that. I...
|
Forum: MechMates already cutting
Tue 12 August 2008, 13:25
|
Replies: 231
Views: 231,784
Snake
Thanks for the kind words guys. I stumbled upon a site yesterday that has some nice wood carving patterns. I bought a few to try with the MM. I think I can design some nice Christmas gifts with...
|
Forum: MechMates already cutting
Mon 11 August 2008, 08:26
|
Replies: 231
Views: 231,784
logo'ed
I finally got my neighbor to make my logos for me this weekend and I got them on my MM. Guess that was the last thing needed to complete it. Someday I might make a fancy dust foot for looks, but it...
|
Forum: MechMates already cutting
Wed 06 August 2008, 17:12
|
Replies: 231
Views: 231,784
that sounds like it could work. I was concerned...
that sounds like it could work. I was concerned that cutting something so flimsy that the tool might try to grab it and pull the whole sheet of rubber to the router, but sandwiched like + the screws,...
|
Forum: MechMates already cutting
Wed 06 August 2008, 15:33
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Wed 06 August 2008, 11:27
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Wed 06 August 2008, 09:50
|
Replies: 231
Views: 231,784
Gerald, I was cutting some small circles out of...
Gerald, I was cutting some small circles out of light ply today and when I finished and hit the ref home key, my z axis and y axis are moving about 3/4 to 1 inch away from the proximity sensor hole....
|
Forum: MechMates already cutting
Fri 20 June 2008, 10:50
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Fri 20 June 2008, 10:17
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Fri 20 June 2008, 10:08
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Fri 20 June 2008, 08:21
|
Replies: 231
Views: 231,784
Gerald,
I was thinking of the wiring layout...
Gerald,
I was thinking of the wiring layout that you had drawn to show the layout of the Proxies and the relays (it was a nice drawing). A schematic is good but sometimes a wiring layout like my...
|
Forum: MechMates already cutting
Thu 19 June 2008, 15:49
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Fri 13 June 2008, 14:05
|
Replies: 231
Views: 231,784
finished cab fingerjointed with MM
The finger joints that I had cut in the earlier photo turned out way better than I could have imagined them to. It was also probably faster than using my dovetail jig also. I like the fit and the...
|
Forum: MechMates already cutting
Sat 07 June 2008, 11:31
|
Replies: 231
Views: 231,784
Thanks guys that makes sense to me, and seems...
Thanks guys that makes sense to me, and seems like it would be easier to build by attatching to the z car rather than the slide. I don't mind sweeping some of the larger stuff as long as it gets most...
|
Forum: MechMates already cutting
Sat 07 June 2008, 09:43
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Thu 05 June 2008, 08:56
|
Replies: 231
Views: 231,784
|
Forum: MechMates already cutting
Wed 04 June 2008, 13:49
|
Replies: 231
Views: 231,784
Hi Heath,
I was going to grind my own rails...
Hi Heath,
I was going to grind my own rails and I got bad cutts on the y rails so I took the crooked cutt pieces to a friend that has a mill and had them milled down to 7/8". If I ever do another...
|