Forum: 40. Z-Slide
Tue 18 August 2009, 07:16
|
Replies: 86
Views: 102,286
Extended Z-slide summary
To All,
I have received a few emails lately on the performance and details on the slide extension I have modified for foam cutting.
In summary:
What is the Z-slide made of?
- W6" x 4.7#/ft...
|
Forum: 40. Z-Slide
Sun 15 March 2009, 19:17
|
Replies: 86
Views: 102,286
Nicely done Art.
Today I was able to rotate the...
Nicely done Art.
Today I was able to rotate the router 180 degree's and have the cord exit the rear next to the slide. Final stiffener bracket is in the works.
I have to add "one more rotation" on...
|
Forum: 40. Z-Slide
Sat 14 March 2009, 07:44
|
Replies: 86
Views: 102,286
Gerald and JR.
You are both correct.
I have 2...
Gerald and JR.
You are both correct.
I have 2 router heads. One is the 7518 model which is single speed (for foam) and the 7519 model which I use for wood, metal, etc. So, you both are correct. ...
|
Forum: 40. Z-Slide
Sat 14 March 2009, 05:32
|
Replies: 86
Views: 102,286
...Planned, just not installed yet!
That's...
...Planned, just not installed yet!
That's todays metal working challenge. For the life of me I couldn't wrap my head around that electrical cord exit, so I just said I will cut something to fit in...
|
Forum: 40. Z-Slide
Fri 13 March 2009, 19:11
|
Replies: 86
Views: 102,286
Heath,
I had a problem with the hole on the...
Heath,
I had a problem with the hole on the that side of the slide.
I needed to get cutting, so I left 1 bearing off. The threads were tapped slightly not square and was causing the bearing to...
|
Forum: 40. Z-Slide
Fri 13 March 2009, 15:35
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Sat 31 January 2009, 08:44
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Sat 31 January 2009, 05:20
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Fri 30 January 2009, 13:45
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Thu 29 January 2009, 08:50
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Wed 28 January 2009, 19:35
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Wed 28 January 2009, 12:04
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Sat 27 December 2008, 07:03
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Mon 25 August 2008, 13:30
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Mon 11 August 2008, 18:50
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Sun 10 August 2008, 19:14
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Wed 06 August 2008, 17:41
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Wed 06 August 2008, 17:39
|
Replies: 86
Views: 102,286
Matthew,
It's nice to see you finally paying...
Matthew,
It's nice to see you finally paying attention to us little people in florida.
I have made allowances for the z-slide. For one, I am using alum flat bar with the machined rails for the...
|
Forum: 40. Z-Slide
Tue 05 August 2008, 19:43
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Tue 05 August 2008, 18:38
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Tue 05 August 2008, 08:41
|
Replies: 86
Views: 102,286
|
Forum: 40. Z-Slide
Tue 05 August 2008, 06:31
|
Replies: 86
Views: 102,286
Chiming in will be no problem.
I have already...
Chiming in will be no problem.
I have already sent the new, longer and larger spider to laser cutting.
I hope to have it back in a week or two. It's on the LOW priority list at the cutters. They...
|
Forum: 40. Z-Slide
Mon 04 August 2008, 11:24
|
Replies: 86
Views: 102,286
Greg,
I actually have a bolt together table so...
Greg,
I actually have a bolt together table so I can remove the center of the table and cut up to 48" below the Gantry as designed. I am currently remaking my Z-slide with a few Gerald suggested...
|