MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 9 of 9
Search took
0.00
seconds.
Search:
Posts Made By:
smreish
Forum:
MechMates already cutting
Fri 07 October 2022, 07:07
Replies:
479
Work Horse Rebuild - Lac-Brome, Quebec, CA
Views:
539,273
Posted By
smreish
HI Robert - so good to see you back in the...
HI Robert - so good to see you back in the thread. I quietly lurk.
The last 2 machines from 2008 still running fine, but haven't found a better low cost solution to the PMDX / smooth stepper / Mach...
Forum:
MechMates already cutting
Sun 26 October 2014, 07:44
Replies:
479
Work Horse Rebuild - Lac-Brome, Quebec, CA
Views:
539,273
Posted By
smreish
...I put cow pushers on my #5 too. More for...
...I put cow pushers on my #5 too. More for keeping the airborne foam bits from sticking to the rail. Yes, I have had my share of shop rags get run over....and the proxies detected the lift every...
Forum:
MechMates already cutting
Wed 26 December 2012, 08:25
Replies:
479
Work Horse Rebuild - Lac-Brome, Quebec, CA
Views:
539,273
Posted By
smreish
I drilled all the way thru both legs of the c...
I drilled all the way thru both legs of the c channel cross bearers for this reason.
I used a 3/16 pilot hole for both legs, then tapped the top member.
Every time I have replaced the MAIN...
Forum:
MechMates already cutting
Tue 01 December 2009, 05:03
Replies:
479
Work Horse Rebuild - Lac-Brome, Quebec, CA
Views:
539,273
Posted By
smreish
Robert, Nice work. But is it really necessary?...
Robert,
Nice work. But is it really necessary? While your solution to a "problem" that didn't exist appears to add cost and time to the build. I don't understand why you would add the...
Forum:
MechMates already cutting
Sat 07 November 2009, 09:42
Replies:
479
Work Horse Rebuild - Lac-Brome, Quebec, CA
Views:
539,273
Posted By
smreish
Robert, I have done both. The bolt option...
Robert, I have done both.
The bolt option works, it's just a bit of a pain to align the washer on each and every one as you move along. I would make sure NOT to over drill the beam hole and...
Forum:
MechMates already cutting
Tue 03 November 2009, 18:09
Replies:
479
Work Horse Rebuild - Lac-Brome, Quebec, CA
Views:
539,273
Posted By
smreish
...exactly how I did my z-slides.
...exactly how I did my z-slides.
Forum:
MechMates already cutting
Fri 25 September 2009, 17:17
Replies:
479
Work Horse Rebuild - Lac-Brome, Quebec, CA
Views:
539,273
Posted By
smreish
Robert I responded in email. Email me again...
Robert
I responded in email. Email me again if you need more! merci
Forum:
MechMates already cutting
Fri 25 September 2009, 08:04
Replies:
479
Work Horse Rebuild - Lac-Brome, Quebec, CA
Views:
539,273
Posted By
smreish
Robert, I know Gerald asked the question, but I...
Robert,
I know Gerald asked the question, but I will again.
Did you not wire your transformer outputs correctly? I was reviewing your schematic again and you should be somewhere in the 40 volt...
Forum:
MechMates already cutting
Tue 15 September 2009, 06:04
Replies:
479
Work Horse Rebuild - Lac-Brome, Quebec, CA
Views:
539,273
Posted By
smreish
Robert, Nice drawing! Looks a little familiar...
Robert,
Nice drawing! Looks a little familiar :)
I am glad to see you moving along and getting to the starting line.
Chat with you soon....you know the number!
Sean
Showing results 1 to 9 of 9
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
05:09
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.