Forum: MechMates already cutting
Wed 27 April 2011, 07:29
|
Replies: 440
Views: 835,308
Note:
If your using standard 4 pin connectors...
Note:
If your using standard 4 pin connectors m4/m12 on a 45mm body sensor or longer, you will need to enlarge that hole to about 19mm so the bonnet on the shell will screw on the proximity body. ...
|
Forum: MechMates already cutting
Sun 30 January 2011, 05:49
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Mon 24 January 2011, 12:53
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Fri 21 January 2011, 08:00
|
Replies: 440
Views: 835,308
Mike,
I had 3 lights on the front of the...
Mike,
I had 3 lights on the front of the control cabinet for the following (all wired thru the contactor aux contact)
- power to cabinet (blinks when machine is actually cutting)
- spindle on
-...
|
Forum: MechMates already cutting
Thu 06 January 2011, 10:57
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Sat 27 November 2010, 09:58
|
Replies: 440
Views: 835,308
Tony
Genius idea about the coolant reservoir...
Tony
Genius idea about the coolant reservoir and level indicator.
Hopefully I didn't embarras you publicly about the connectors....your right; you really only make the connection once. But is...
|
Forum: MechMates already cutting
Sat 20 November 2010, 12:12
|
Replies: 440
Views: 835,308
Tony,
Nice panel work. Be careful about the...
Tony,
Nice panel work. Be careful about the Male 4 pin connectors you used. The choice of male sex on the panel will allow motor voltage to be touched by your fingers if energized when not...
|
Forum: MechMates already cutting
Sat 23 October 2010, 05:58
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Sat 16 October 2010, 12:26
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Sat 16 October 2010, 09:25
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Tue 12 October 2010, 17:45
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Mon 11 October 2010, 09:41
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Sat 14 August 2010, 14:25
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Fri 04 June 2010, 17:40
|
Replies: 440
Views: 835,308
Understood.
Also, since I have my quality...
Understood.
Also, since I have my quality control hat on. Remember that the Y car stops are shorter than the ones used on the x - axis. You might have to take about 4-7mm off the y car set to make...
|
Forum: MechMates already cutting
Fri 04 June 2010, 13:50
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Thu 27 May 2010, 13:01
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Thu 15 October 2009, 13:07
|
Replies: 440
Views: 835,308
|
Forum: MechMates already cutting
Wed 02 September 2009, 18:27
|
Replies: 440
Views: 835,308
|