MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 8 of 8
Search took
0.00
seconds.
Search:
Posts Made By:
smreish
Forum:
Troubleshooting
Wed 20 October 2010, 09:03
Replies:
22
Spindle RF noise makes y car & z axis move
Views:
25,002
Posted By
smreish
Gentlemen, Thanks for chiming in. The purpose...
Gentlemen,
Thanks for chiming in. The purpose of the question was 2 fold - to spur critical thought and also add to the troubleshooting threads in the forum.
I have a new cable on order, and...
Forum:
Troubleshooting
Tue 19 October 2010, 18:23
Replies:
22
Spindle RF noise makes y car & z axis move
Views:
25,002
Posted By
smreish
Today a new issue arrived on Machine #58. ...
Today a new issue arrived on Machine #58.
Symptom - while changing spindle speed from 18K down to 60 rpm for special milling procedure, the Z - axis would "step abruptly in the down or up...
Forum:
Troubleshooting
Sat 26 September 2009, 08:59
Replies:
22
Spindle RF noise makes y car & z axis move
Views:
25,002
Posted By
smreish
Mike, Thanks for publishing that clarification....
Mike,
Thanks for publishing that clarification. I guess in my haste that I should have said " a line reactor may give you the same results as the isolation transformer - by isolating and not...
Forum:
Troubleshooting
Fri 25 September 2009, 17:31
Replies:
22
Spindle RF noise makes y car & z axis move
Views:
25,002
Posted By
smreish
David Line reactor is very similar.....just a...
David
Line reactor is very similar.....just a few minor insignificant differences. The line reactor is VERY recommended from all drive manufactures when using a spindle. EMF affects machines...
Forum:
Troubleshooting
Mon 21 September 2009, 19:23
Replies:
22
Spindle RF noise makes y car & z axis move
Views:
25,002
Posted By
smreish
David, Great to hear you have it working. It...
David,
Great to hear you have it working.
It sounds like the you solved the inverter issue. I would venture to guess if you added an isolation transformer before the inverter, you would have...
Forum:
Troubleshooting
Mon 29 June 2009, 08:27
Replies:
22
Spindle RF noise makes y car & z axis move
Views:
25,002
Posted By
smreish
Round three of electrical noise. Problem: ...
Round three of electrical noise.
Problem:
The Pmdx is seeing the "ground flutter" the stepper motors were seeing. Only on the sourced inputs which are pins 11, 12, 13 and 15.
Solution:
...
Forum:
Troubleshooting
Fri 26 June 2009, 17:30
Replies:
22
Spindle RF noise makes y car & z axis move
Views:
25,002
Posted By
smreish
All clean now. Whew - that was exhausting. I...
All clean now.
Whew - that was exhausting. I had 2 sources of noise.
What was done:
-I ran new motor cable that had a double braid and foil shield. (prior motor cables only had a foil screen)...
Forum:
Troubleshooting
Wed 24 June 2009, 13:45
Replies:
22
Spindle RF noise makes y car & z axis move
Views:
25,002
Posted By
smreish
Spindle RF noise makes y car & z axis move
Well,
The machine moves well, performs and executes G-code fine.
...then I turned on the spindle. Yikes....talk about cross talk in the wires.
The spindle turned on at 500 rpm or higher the y car...
Showing results 1 to 8 of 8
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
21:50
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.