Forum: Construction started, but not cutting yet
Thu 13 March 2014, 21:47
|
Replies: 124
Views: 126,259
I have been off wandering. I wanted to find out...
I have been off wandering. I wanted to find out more about electronics so I bought a book and started to read, but I wanted some hands on. I bumped into a radio ham operator and he invited me to a...
|
Forum: Construction started, but not cutting yet
Thu 23 January 2014, 21:23
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Thu 23 January 2014, 20:54
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Thu 23 January 2014, 18:26
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Tue 21 January 2014, 23:54
|
Replies: 124
Views: 126,259
I saw a way to machine the plates for the...
I saw a way to machine the plates for the reduction drive. Since I am interested in learning various ways of machining the same part I tried to faceplate on the lathe. The chuck on my lathe uses...
|
Forum: Construction started, but not cutting yet
Sat 18 January 2014, 18:07
|
Replies: 124
Views: 126,259
The large drill bits I ordered showed up. The...
The large drill bits I ordered showed up. The largest is 1 inch so I can step drill them up to 1 inch and bore to 1.125. I tried it on the mill and then I wanted to try it on the lathe. My lathe has...
|
Forum: Construction started, but not cutting yet
Fri 10 January 2014, 22:48
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Fri 10 January 2014, 17:01
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Thu 09 January 2014, 23:41
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Sat 04 January 2014, 11:01
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Fri 03 January 2014, 22:19
|
Replies: 124
Views: 126,259
spent the day playing on the vertical mill. I...
spent the day playing on the vertical mill. I drilled the alignment holes between the top and bottom plates of the reduction drives. If you need the assembly to face one direction you just turn over...
|
Forum: Construction started, but not cutting yet
Wed 01 January 2014, 22:09
|
Replies: 124
Views: 126,259
completed my mock up reduction drive. I was...
completed my mock up reduction drive. I was mostly satisfied with the results. The setup I am aiming for is 4:1 but I made the setup so that it can go far higher if I need to. Today I used the new...
|
Forum: Construction started, but not cutting yet
Mon 23 December 2013, 18:42
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Sun 22 December 2013, 18:25
|
Replies: 124
Views: 126,259
Well I had hoped to get the bandsaw mounted on...
Well I had hoped to get the bandsaw mounted on the cart today but as I looked around the neighborhood and saw all the Christmas lights I decide the least I could do is clean up the wood stacked...
|
Forum: Construction started, but not cutting yet
Sat 21 December 2013, 23:40
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Thu 19 December 2013, 22:11
|
Replies: 124
Views: 126,259
I was able to get the carriage stop cut out of...
I was able to get the carriage stop cut out of bar stock and mill almost all the relief. Decided to wait until tomorrow to fine tune it. The band saw didn't arrive until 7:00. Dug out the pry bars...
|
Forum: Construction started, but not cutting yet
Thu 19 December 2013, 22:04
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Wed 18 December 2013, 20:54
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Wed 18 December 2013, 18:01
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Thu 12 December 2013, 22:22
|
Replies: 124
Views: 126,259
|
Forum: Construction started, but not cutting yet
Thu 12 December 2013, 17:23
|
Replies: 124
Views: 126,259
Table
Well rails are done except that I need to replace one. Ordered new v groove rail from McMaster Carr. Y axis is in progress. As soon as I get two rectangular tubes cut and welded I am going to move...
|
Forum: Construction started, but not cutting yet
Sat 07 December 2013, 16:19
|
Replies: 124
Views: 126,259
Y done x in progress
finished putting the v grooves on the y axis so they are done and ready to mount on the carriage. finished mounting the v groove on the x axis. It is ready to mount on the table. The last x axis got...
|
Forum: Construction started, but not cutting yet
Fri 06 December 2013, 17:49
|
Replies: 124
Views: 126,259
Rails and Paint
The y rails dried over night and looks good. I screwed the v groove in place with stainless steel screws and lock nuts. I took the camera out to the garage and never took one shot. I did finish...
|
Forum: Construction started, but not cutting yet
Wed 04 December 2013, 19:39
|
Replies: 124
Views: 126,259
Y-Axis
I worked on the Y-axis today. I drilled all the holes needed to mound the v-groove rails. I then took a 7 inch flap grinder to the rails. I removed all the scale and rust. I made sure that all the...
|
Forum: Construction started, but not cutting yet
Fri 29 November 2013, 16:45
|
Replies: 124
Views: 126,259
In Gear for Reduction Drives
Finally crated the bandsaw and it is ready to go back to Grizzly. I am tired that thing weight 600lbs before crating. I finished turning the gears I need for the reduction drive. Need to figure what...
|