MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 10 of 10
Search took
0.00
seconds.
Search:
Posts Made By:
pblackburn
Forum:
Troubleshooting
Thu 28 May 2015, 19:47
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
You should run to the star ground in theory and...
You should run to the star ground in theory and all grounds run to it. That would be the correct way. That being said, I have seen that law broken and not had problems.
Did you leave the...
Forum:
Troubleshooting
Thu 28 May 2015, 19:43
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
If you have a dial indicator, you could write...
If you have a dial indicator, you could write code to make the machine run in the X for the length of the machine and back lets say 10 times. I would do both at feedrate and then 2nd test with rapid...
Forum:
Troubleshooting
Thu 28 May 2015, 19:34
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
are your cables shielded to the steppers?
are your cables shielded to the steppers?
Forum:
Troubleshooting
Thu 28 May 2015, 19:12
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
All step low active and dir low active have a red...
All step low active and dir low active have a red x in them on mine
Forum:
Troubleshooting
Thu 28 May 2015, 19:09
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
I will go down and look at mine
I will go down and look at mine
Forum:
Troubleshooting
Thu 28 May 2015, 18:48
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
Lee, I feel your pain, I had problems...
Lee, I feel your pain, I had problems intermittently with mine. They can hide and make you want to pull your hair out. I am practically doing that here trying to think of what your problem is...
Forum:
Troubleshooting
Thu 28 May 2015, 18:24
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
I have run 250IPM cutting HDPE. 180IPM with 1/2"...
I have run 250IPM cutting HDPE. 180IPM with 1/2" bit in 3/4 plywood. There is something else amiss here. Something that is being overlooked.
Forum:
Troubleshooting
Sun 24 May 2015, 15:11
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
Lee, I have a 7.2 reduction and my velocity...
Lee,
I have a 7.2 reduction and my velocity and acceleration are 500 and 50. I think you have something else going on. Kernal needs to 35k. Other thing to try is turn off the toolpath preview. I...
Forum:
Troubleshooting
Sun 24 May 2015, 14:54
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
If it is a 7.2 gearbox it will be around 0.0003...
If it is a 7.2 gearbox it will be around 0.0003 per step. You can calculate it out.
Forum:
Troubleshooting
Sun 24 May 2015, 12:35
Replies:
49
Cutting errors - slop in motors?
Views:
59,267
Posted By
pblackburn
Spur geared motors will have play also. They...
Spur geared motors will have play also. They have to or they will rip themselves apart. It will be less than 10 thousandths but will increases over time. Just know it is there. To find out how...
Showing results 1 to 10 of 10
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
21:50
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.