MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Showing results 1 to 9 of 9
Search took 0.00 seconds.
Search: Posts Made By: JasonC
Forum: MechMates already cutting Tue 13 December 2011, 20:16
Replies: 137
Views: 138,567
Posted By JasonC
On output Signal?. Output #1, enabled yes, port...

On output Signal?. Output #1, enabled yes, port #1, pin number 16 active low yes. I have nothing else at this time for the rest.

Jason
Forum: MechMates already cutting Mon 12 December 2011, 20:29
Replies: 137
Views: 138,567
Posted By JasonC
Ok fired up my CNC computer. In motor outputs I...

Ok fired up my CNC computer. In motor outputs I have .
X Axis enabled Yes, Step Pin #3 Dir Pin #2. Dir Low No,Step low Yes, Step Port 1,Dir Port 1
Y axis enable yes, step Pin #5,Dir Pin #4, Dir...
Forum: MechMates already cutting Mon 12 December 2011, 20:03
Replies: 137
Views: 138,567
Posted By JasonC
Ya, also what you have said happened to me. It...

Ya, also what you have said happened to me. It would go out and I think I could here a relay trip. I was doing something else(which I cant remember) then all the lights would reset and come back...
Forum: MechMates already cutting Mon 12 December 2011, 19:56
Replies: 137
Views: 138,567
Posted By JasonC
My JP4 is different, its in the on. and cant see...

My JP4 is different, its in the on. and cant see JP3 but mine is off, which is strange because its to power the smoothsteper..lol
Forum: MechMates already cutting Mon 12 December 2011, 08:54
Replies: 137
Views: 138,567
Posted By JasonC
Can you shoot us a good detailed pic of the top...

Can you shoot us a good detailed pic of the top of your PMDX-126?

Jason
Forum: MechMates already cutting Mon 28 November 2011, 10:39
Replies: 137
Views: 138,567
Posted By JasonC
Im pretty sure that my setup had the same problem...

Im pretty sure that my setup had the same problem with the comunication via the printer port. Everything still sound the same as what I went through. Is it possible to borrow a Smoothstepper just to...
Forum: MechMates already cutting Sat 26 November 2011, 10:32
Replies: 137
Views: 138,567
Posted By JasonC
Any luck? Ill check my pins and ports today....

Any luck? Ill check my pins and ports today. Also if you can use the SmoothStepper, everything you said sounds just like what I went through to a T.

Jas
Forum: MechMates already cutting Wed 23 November 2011, 08:57
Replies: 137
Views: 138,567
Posted By JasonC
One other thing i noticed is Im using a...

One other thing i noticed is Im using a Smoothstepper USB. My computer wouldnt move the motors without it.

Also my pins and ports I had to follow the manual that Mike suggested and I also...
Forum: MechMates already cutting Tue 22 November 2011, 08:55
Replies: 137
Views: 138,567
Posted By JasonC
I had similiar problems, I wired mine Bipolar...

I had similiar problems, I wired mine Bipolar parallel then corrected my pins and ports.

Jason
Showing results 1 to 9 of 9

 
Forum Jump

All times are GMT -6. The time now is 02:53.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.