MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 9 of 9
Search took
0.00
seconds.
Search:
Posts Made By:
Richards
Forum:
Troubleshooting
Thu 15 November 2007, 10:48
Replies:
45
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault
Views:
44,802
Posted By
Richards
Gerald, Yes, Inductance is the important...
Gerald,
Yes, Inductance is the important measurement. And, just as you pointed out, winding matching coils by counting turns and using wire from the same spool is about the only way that most of us...
Forum:
Troubleshooting
Thu 15 November 2007, 09:35
Replies:
45
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault
Views:
44,802
Posted By
Richards
Daya, Gerald's suggestion to use a GFI is...
Daya,
Gerald's suggestion to use a GFI is very important. The GFI will protect you and your equipment if current starts to flow through the Earth Ground.
The difference between 5 ohms and 4.6...
Forum:
Troubleshooting
Thu 15 November 2007, 05:39
Replies:
45
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault
Views:
44,802
Posted By
Richards
This is something that I know nothing about. ...
This is something that I know nothing about. However, I think that having the windings on the A coil match the windings on the B coil would be necessary. To me the bigger problem would be...
Forum:
Troubleshooting
Thu 08 November 2007, 05:17
Replies:
45
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault
Views:
44,802
Posted By
Richards
Hi guys, Sorry, but I slept in until 4:45...
Hi guys,
Sorry, but I slept in until 4:45 a.m. this morning. It looks like you've found the problem. I just checked two of my PK296B2A-SG3.6 motors. With the power off, the gear shaft, without...
Forum:
Troubleshooting
Wed 07 November 2007, 04:59
Replies:
45
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault
Views:
44,802
Posted By
Richards
I just checked the voltage between a G202 and its...
I just checked the voltage between a G202 and its motor. In standby, there is less than one volt showing on the meter; however, the LED on the G202 is bright. Do you have 56V going into all of the...
Forum:
Troubleshooting
Wed 07 November 2007, 04:50
Replies:
45
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault
Views:
44,802
Posted By
Richards
We cross posted again. It's a good sign that the...
We cross posted again. It's a good sign that the LED's on the Geckos are working without motors attached. Voltage between the G202 and the motor depends on which coil(s) is active at any particular...
Forum:
Troubleshooting
Wed 07 November 2007, 04:41
Replies:
45
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault
Views:
44,802
Posted By
Richards
How is your controller connected to power? Do...
How is your controller connected to power? Do you use a two-prong reversible plug? Do you have the controller hard-wired to a breaker/fuse panel? Has anyone re-wired the connections between the...
Forum:
Troubleshooting
Wed 07 November 2007, 04:06
Replies:
45
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault
Views:
44,802
Posted By
Richards
Hi Gerald. It's good to have good friends on...
Hi Gerald. It's good to have good friends on line at 4:00 a.m.
Forum:
Troubleshooting
Wed 07 November 2007, 03:58
Replies:
45
Stepper motors giving trouble - Motors burnt while serving as ground for elec. fault
Views:
44,802
Posted By
Richards
Can you tell us what is working? Is the E-stop...
Can you tell us what is working? Is the E-stop switch working? Are the power supplies all generating power? Are the LEDs on all devices properly lit? Do the direction LEDs turn on/off when you...
Showing results 1 to 9 of 9
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
19:29
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.