MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 5 of 5
Search took
0.00
seconds.
Search:
Posts Made By:
Richards
Forum:
60. Wiring & Cable Management
Sat 02 August 2008, 07:21
Replies:
107
Grounding or Earthing
Views:
131,356
Posted By
Richards
Ideally, a shield or drain conductor should only...
Ideally, a shield or drain conductor should only be connected at one end. The purpose of the shield is to reduce EMI type interference along the entire length of the cable for that one device. By...
Forum:
60. Wiring & Cable Management
Fri 07 September 2007, 05:33
Replies:
107
Grounding or Earthing
Views:
131,356
Posted By
Richards
Greg, I'm BYU True Blue, through and through. ...
Greg,
I'm BYU True Blue, through and through. The U of Utah Red is the most likely cause of my high blood pressure (especially during football season, late in the season when BYU and that other...
Forum:
60. Wiring & Cable Management
Thu 06 September 2007, 15:46
Replies:
107
Grounding or Earthing
Views:
131,356
Posted By
Richards
All ground connections should be at the same...
All ground connections should be at the same voltage level. Ground is the point from which you measure all other voltages. Good practice is to connect the 'ground' from each circuit to the same...
Forum:
60. Wiring & Cable Management
Thu 06 September 2007, 11:34
Replies:
107
Grounding or Earthing
Views:
131,356
Posted By
Richards
If you use the Green/Yellow grounding terminal...
If you use the Green/Yellow grounding terminal blocks, they're designed to pass anything that's connected to that particular terminal block directly to the DIN rail. In that case, it would be...
Forum:
60. Wiring & Cable Management
Fri 17 August 2007, 07:51
Replies:
107
Grounding or Earthing
Views:
131,356
Posted By
Richards
If possible unscrew the covers from each end of...
If possible unscrew the covers from each end of the parallel cable to see if the shield is just soldered to the metal part of the connector. If that is the situation, cut the shield conductor and...
Showing results 1 to 5 of 5
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
18:07
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.