Forum: MechMates already cutting
Tue 16 May 2017, 09:39
|
Replies: 75
Views: 134,446
It is alive
I got the thing moving... I even crashed it one or two time :D :confused:
I got V carve pro 8.5 and Fusion 360. There is a lot to learn the curve is just about strait up. I fly cut the table, that...
|
Forum: MechMates already cutting
Tue 16 May 2017, 09:10
|
Replies: 75
Views: 134,446
Water Cooling
I got the water cooler setup along with the radiator and 3 fans. The water pump and fans startup with Mach4 calls for the spindle to start. work great so far.
As you can almost see the water flow...
|
Forum: MechMates already cutting
Wed 29 March 2017, 08:17
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Wed 29 March 2017, 08:12
|
Replies: 75
Views: 134,446
The stepper drivers are mounted to that on the...
The stepper drivers are mounted to that on the inside, I cut out the side of the box to the size of the heat sink less 3/8" all around to seal and bolt it on. The drivers are bolt on to the heat sink...
|
Forum: MechMates already cutting
Wed 29 March 2017, 08:07
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Tue 28 March 2017, 13:52
|
Replies: 75
Views: 134,446
Every thing is level and rolling smooth. Still...
Every thing is level and rolling smooth. Still got the Z to do. Looking at water cooled spindle, alone with a cooler and pump set on the Y cart. This making the run short and the system will be right...
|
Forum: MechMates already cutting
Tue 28 March 2017, 13:46
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Tue 28 March 2017, 13:44
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Wed 22 March 2017, 08:14
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Tue 21 March 2017, 10:30
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Mon 20 March 2017, 13:39
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Mon 20 March 2017, 13:31
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Mon 20 March 2017, 13:30
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Mon 20 March 2017, 13:21
|
Replies: 75
Views: 134,446
This is how I got the Gantry rail bolted to the...
This is how I got the Gantry rail bolted to the gantry. I used a rod that I threaded on one end, put the clamping plate inside the gantry tubes and threaded the shafts in the clamping plate on both...
|
Forum: MechMates already cutting
Mon 20 March 2017, 13:13
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Mon 20 March 2017, 13:12
|
Replies: 75
Views: 134,446
Here is how I adjusted the rails to be level.....
Here is how I adjusted the rails to be level.. Then I welded the beams to the table for good. The bolts were to adjust the beam, I had three of them on each beam, one on both ends and one in the...
|
Forum: MechMates already cutting
Tue 14 March 2017, 07:44
|
Replies: 75
Views: 134,446
The beam was not that wide (4") for the head of...
The beam was not that wide (4") for the head of the bolts to ride on. I placed the board on the beam and the rail on top of that and clamped it all down to the beam. This was flat and worked great...
|
Forum: MechMates already cutting
Mon 13 March 2017, 12:07
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Mon 13 March 2017, 11:58
|
Replies: 75
Views: 134,446
Main rails
After we got the rails done we started on the main I beams. got them cut off to size and cleaned up before they get leveled up and welded. I drilled and tapped three 1/4 20 in the I beam bottom leg....
|
Forum: MechMates already cutting
Mon 13 March 2017, 11:53
|
Replies: 75
Views: 134,446
Rails have started
This weekend I worked on my V rails. This was a big pain in the A##. I have over 12 hours in just cutting off and v grinding the rail... It is done and I,m glad. I think the out come was good and...
|
Forum: MechMates already cutting
Wed 01 March 2017, 12:34
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Wed 01 March 2017, 12:33
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Tue 28 February 2017, 13:44
|
Replies: 75
Views: 134,446
|
Forum: MechMates already cutting
Mon 27 February 2017, 14:15
|
Replies: 75
Views: 134,446
Pics of build
Every thing starting to come together. All this is just mocked up to see if they fit and move as they should. Still got my v rail that need to be ground, I will have to stop putting them off here...
|
Forum: MechMates already cutting
Mon 27 February 2017, 14:10
|
Replies: 75
Views: 134,446
|