Forum: General - MM Build
Fri 22 March 2013, 09:32
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Thu 08 December 2011, 06:13
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Tue 22 November 2011, 22:25
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Wed 12 May 2010, 00:04
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Sat 05 December 2009, 05:20
|
Replies: 55
Views: 97,018
Drawings 10 20 200 A and 10 20 225 A:
-...
Drawings 10 20 200 A and 10 20 225 A:
- Show the clamp strip in cross-section, showing the tapped hole
- Add the gantry tube in cross-section, through a hole
- Add another view with the...
|
Forum: General - MM Build
Wed 25 November 2009, 22:06
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Tue 06 October 2009, 23:23
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Mon 21 September 2009, 07:39
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Mon 31 August 2009, 21:08
|
Replies: 55
Views: 97,018
Drawing 10 60 100 A should explain in what...
Drawing 10 60 100 A should explain in what direction the two views are. The top view is the "back" of the MM - looking from y=max towards y=0. (From far side towards near side) The bottom view is...
|
Forum: General - MM Build
Mon 10 August 2009, 23:29
|
Replies: 55
Views: 97,018
M2 30 110 T A
Remove the [3/16" or 1/4"...
M2 30 110 T A
Remove the [3/16" or 1/4" UNC] and replace with [10-32 or 1/4-28]
See "Grub"/set scews for pinion gears, with LocTite ? (http://www.mechmate.com/forums/showthread.php?t=795)
|
Forum: General - MM Build
Tue 04 August 2009, 00:24
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Sun 02 August 2009, 22:49
|
Replies: 55
Views: 97,018
Following received via PM:
There used to be...
Following received via PM:
There used to be a forum for suggested changes, but I couldn't find it.
1) the title block of drawing 10 40 104 indicates that it is for the 250mm z-slide. It is...
|
Forum: General - MM Build
Thu 23 July 2009, 01:27
|
Replies: 55
Views: 97,018
Add a note to 10 10 302 S:
If an...
Add a note to 10 10 302 S:
If an alternative to the specified C-section is considered, ensure that a minimum cross section moment of inertia (Ixx) value of 0.70 x 106 mm4 [1.4 in4] is maintained....
|
Forum: General - MM Build
Thu 28 May 2009, 07:48
|
Replies: 55
Views: 97,018
Support board thickness:
"I relooked at the...
Support board thickness:
"I relooked at the drawing today and see that I said 24mm max under the screwhead. That was because of the screw length. I should also have given a minimum and that would...
|
Forum: General - MM Build
Sat 21 March 2009, 23:31
|
Replies: 55
Views: 97,018
See these posts before the last drawing...
See these posts before the last drawing revisions:
http://www.mechmate.com/forums/showthread.php?p=13310&postcount=20
The slots have been removed. Now use countersunk screws to hold the geared...
|
Forum: General - MM Build
Tue 23 December 2008, 13:01
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Thu 18 December 2008, 19:27
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Wed 26 November 2008, 05:19
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Sat 23 August 2008, 00:23
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Thu 14 August 2008, 10:23
|
Replies: 55
Views: 97,018
It is plain coincidence that most of the MM...
It is plain coincidence that most of the MM drawings have the revs of the P and B drawings tracking each other. The rev only gets changed when the older drawing can cause a mistake. For example, if a...
|
Forum: General - MM Build
Thu 14 August 2008, 09:03
|
Replies: 55
Views: 97,018
10 20 456 P A is the latest revision of the...
10 20 456 P A is the latest revision of the Profile cut drawing for that part
10 20 456 B B is the latest revision of the Bend drawing for that part
The reason for the Bend drawing having a...
|
Forum: General - MM Build
Sun 10 August 2008, 05:16
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Sat 02 August 2008, 11:33
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Fri 01 August 2008, 22:47
|
Replies: 55
Views: 97,018
|
Forum: General - MM Build
Fri 01 August 2008, 22:40
|
Replies: 55
Views: 97,018
Bill, drawing 10 10 247 only shows a Drilling...
Bill, drawing 10 10 247 only shows a Drilling process, nothing more. It is indicated by the D in the "Process" block on bottom right. Thus you must read any information on that sheet as it relates to...
|