Forum: 70. Control Systems
Tue 31 January 2012, 22:16
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Wed 14 July 2010, 02:30
|
Replies: 116
Views: 144,409
See this post...
See this post (http://finance.groups.yahoo.com/group/geckodrive/message/20829) on the Gecko yahoo forum, where a G203 owner sent it in for repair and got warned that reversed polarity can damage the...
|
Forum: 70. Control Systems
Tue 13 July 2010, 09:07
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Sun 27 September 2009, 04:00
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Mon 11 May 2009, 23:32
|
Replies: 116
Views: 144,409
I am sure that the PMDX-125 is intended to...
I am sure that the PMDX-125 is intended to replace the PMDX-122 in the course of time. Personally, I would only look seriously at the PMDX-125 after it has been on the market for about a year and has...
|
Forum: 70. Control Systems
Wed 06 May 2009, 11:21
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Fri 27 March 2009, 17:57
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Sat 21 March 2009, 06:47
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Sat 21 March 2009, 05:03
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Sat 21 March 2009, 04:57
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Tue 18 November 2008, 08:15
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Mon 17 November 2008, 06:02
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Mon 10 November 2008, 19:43
|
Replies: 116
Views: 144,409
Further from Steve:
"We ran a test today up...
Further from Steve:
"We ran a test today up to 2 MHz on a PMDX-122 and there was essentially
no signal degradation, but because we fear problems with cable quality and
signal reflections, we...
|
Forum: 70. Control Systems
Sun 09 November 2008, 22:22
|
Replies: 116
Views: 144,409
Over on the geckodrive yahoo group, someone...
Over on the geckodrive yahoo group, someone discovered (http://finance.groups.yahoo.com/group/geckodrive/message/16845) that his breakout board (not a PMDX) was limiting the top speed of his motors....
|
Forum: 70. Control Systems
Wed 10 October 2007, 07:06
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Wed 10 October 2007, 07:04
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Tue 09 October 2007, 11:55
|
Replies: 116
Views: 144,409
|
Forum: 70. Control Systems
Thu 07 June 2007, 23:21
|
Replies: 116
Views: 144,409
Following on from this post...
Following on from this post (http://www.mechmate.com/forums/showthread.php?p=3610&postcount=10) in a power supply thread, Steve Stallings posted this reply...
|