MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Register Options Profile Last 1 | 3 | 7 Days Search Today's Posts Mark Forums Read

Showing results 1 to 8 of 8
Search took 0.00 seconds.
Search: Posts Made By: Gerald D
Forum: CNC motion control software Sun 20 January 2008, 22:09
Replies: 55
Views: 53,930
Posted By Gerald D
Greg, thanks very much for posting that page - I...

Greg, thanks very much for posting that page - I completely forgot about it :o:o

That is the page where you say the router/spindle is controlled from Output #1.

On the page I showed earlier,...
Forum: CNC motion control software Sat 19 January 2008, 14:38
Replies: 55
Views: 53,930
Posted By Gerald D
JR, I think you are looking to make the green...

JR, I think you are looking to make the green tick, plus add 1 and 1 as port and pin, on this screen:

782

And I think that is all there is to it - the relay will then respond on the M03/M05...
Forum: CNC motion control software Fri 18 January 2008, 11:38
Replies: 55
Views: 53,930
Posted By Gerald D
I think it is pin 1. (See table 17 of PMDX-122...

I think it is pin 1. (See table 17 of PMDX-122 manual)

In Mach3, ports & pins, Output Signals, I have Output #1 enabled to port 1, pin 1.

Check if M03 in the G-code turns it on and M05 turns...
Forum: CNC motion control software Fri 11 January 2008, 20:49
Replies: 55
Views: 53,930
Posted By Gerald D
The discussion continued: Question: ...

The discussion continued:

Question:
Brian, in this discussion vein. Can you offer any rough idea's as to future
version's of Mach. I know Art had mentioned about this time last year that "Q"...
Forum: CNC motion control software Fri 11 January 2008, 20:43
Replies: 55
Views: 53,930
Posted By Gerald D
I welcome Brian's response. Mach3 (Mill) already...

I welcome Brian's response. Mach3 (Mill) already has far too much in it for woodwork routing. The curious thing is that there was no mention of Quantum.
Forum: CNC motion control software Fri 11 January 2008, 12:21
Replies: 55
Views: 53,930
Posted By Gerald D
Here is an interesting exchange on the Mach Yahoo...

Here is an interesting exchange on the Mach Yahoo forum. Brian Barker, who picked up the reins from the retired Art Fenerty, replies to Ozzie:

> Is there a published list of development...
Forum: CNC motion control software Mon 07 January 2008, 11:54
Replies: 55
Views: 53,930
Posted By Gerald D
Bernard, Quantum was mentioned in this thread...

Bernard, Quantum was mentioned in this thread (http://www.mechmate.com/forums/showthread.php?t=218) about a year ago. Somehow the excitement of it has died - unless something happened while I was...
Forum: CNC motion control software Wed 24 October 2007, 11:40
Replies: 55
Views: 53,930
Posted By Gerald D
This is the downloads page: ...

This is the downloads page:

http://www.machsupport.com/artsoft/downloads/downloads.htm

It is working now.

We are still using Mach3 Release 1.84.002 (one of the "Release Lockdown"s)
Showing results 1 to 8 of 8

 
Forum Jump

All times are GMT -6. The time now is 04:25.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.