MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 5 of 5
Search took
0.00
seconds.
Search:
Posts Made By:
Gerald D
Forum:
Troubleshooting
Tue 17 March 2009, 13:28
Replies:
11
Cannot get good jog speeds - first thought PS voltage too low, then current error
Views:
11,673
Posted By
Gerald D
Hahaha Krod! :D I have also made a resistor...
Hahaha Krod! :D
I have also made a resistor mistake before, and it sure makes a BIG difference.
Forum:
Troubleshooting
Sun 15 March 2009, 00:31
Replies:
11
Cannot get good jog speeds - first thought PS voltage too low, then current error
Views:
11,673
Posted By
Gerald D
Krod, bear in mind that the voltage increase may...
Krod, bear in mind that the voltage increase may not be the total solution to your low speed problem. You may also have a problem that your PC cannot pump out pulses quickly and smoothly enough....
Forum:
Troubleshooting
Sat 14 March 2009, 21:37
Replies:
11
Cannot get good jog speeds - first thought PS voltage too low, then current error
Views:
11,673
Posted By
Gerald D
Thanks for remembering about the capacitor limits...
Thanks for remembering about the capacitor limits Mike. If Krod has two caps in parallel now, would he be okay to re-wire them serial?
Forum:
Troubleshooting
Sat 14 March 2009, 11:55
Replies:
11
Cannot get good jog speeds - first thought PS voltage too low, then current error
Views:
11,673
Posted By
Gerald D
Krod, you might be able to re-configure the...
Krod, you might be able to re-configure the output windings on your power supply transformer to double your voltage and get the full potential from your motors.
Forum:
Troubleshooting
Fri 13 March 2009, 23:18
Replies:
11
Cannot get good jog speeds - first thought PS voltage too low, then current error
Views:
11,673
Posted By
Gerald D
How did you wire the motor? (halfcoil or series) ...
How did you wire the motor? (halfcoil or series)
What is the voltage of your power supply?
Did you check the Gecko resistors with an Ohm-meter?
Showing results 1 to 5 of 5
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
16:09
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
