MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 13 of 13
Search took
0.00
seconds.
Search:
Posts Made By:
Gerald D
Forum:
CNC motion control software
Sat 20 June 2009, 22:07
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
Their input .sbp code (the stuff you see in the...
Their input .sbp code (the stuff you see in the file with Notepad/wordpad etc.) has always been freely accessible and they promote it as better than g-code. This official "open source" announcement...
Forum:
CNC motion control software
Tue 20 January 2009, 19:37
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
Thanks Jimbo. I think you meant half coil. You...
Thanks Jimbo. I think you meant half coil. You can go up to 75 Volts for the half-coil configuration which will cure the lost steps for jogging. (I think that Campbell runs his boxes on a low voltage...
Forum:
CNC motion control software
Sat 17 January 2009, 12:36
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
Richard, is this what your ShopBot looks like?: ...
Richard, is this what your ShopBot looks like?:
3345
I have no experience of that machine other than the stories I have read about it. Apparently the screw on the Z was prone to getting dirty...
Forum:
CNC motion control software
Sat 17 January 2009, 07:41
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
Repeated question: Are all your ShopBot...
Repeated question: Are all your ShopBot components from before the year 2000? Is it rack & pinion drive or cable drive?
Forum:
CNC motion control software
Sat 17 January 2009, 00:05
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
Are all your ShopBot components from before the...
Are all your ShopBot components from before the year 2000? Is it rack & pinion drive or cable drive?
Forum:
CNC motion control software
Fri 16 January 2009, 22:34
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
Richard C99, let's start at the beginning . . . ....
Richard C99, let's start at the beginning . . . . . what ShopBot do you have? What are the model numbers on the motors? What does the controller look like?
ShopBot changed their configurations...
Forum:
CNC motion control software
Fri 16 January 2009, 10:27
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
Yes, the boxes will run the linked limited G-Code...
Yes, the boxes will run the linked limited G-Code (http://shopbotwiki.com/index.php?title=GCodeMain) but it will be under SB's software. They will not run Mach, EMC or Mach's Quantum like our generic...
Forum:
CNC motion control software
Fri 16 January 2009, 09:43
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
All the ShopBot controller boxes that I know of...
All the ShopBot controller boxes that I know of will only run their software.
Forum:
CNC motion control software
Thu 18 December 2008, 09:06
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
As far as I know, it is still true. It is not a...
As far as I know, it is still true. It is not a problem if you divide the vertical arc into enough straight segments. A good CAM program will take care of this for you.
Forum:
CNC motion control software
Mon 15 December 2008, 05:16
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
In terms of cut quality, there should be no...
In terms of cut quality, there should be no difference between Mach and and SB running on their V201 controller. Both will be doing the same level of micro-stepping of the motors. Mach has always...
Forum:
CNC motion control software
Sat 13 December 2008, 23:27
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
Shopbot software only runs on shopbot hardware....
Shopbot software only runs on shopbot hardware. So, the axes question is related to the capability of the V201 control card from ShopBot - the last time I looked, there wasn't much published about...
Forum:
CNC motion control software
Sat 13 December 2008, 20:48
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
Another difference between Mach and SB . . . . ...
Another difference between Mach and SB . . . .
In Mach we set the acceleration during motor tuning and then forget about it. In SB, they don't have the concept of "acceleration" - they advocate...
Forum:
CNC motion control software
Sat 06 December 2008, 18:59
Replies:
46
Shopbot VS Mach 3
Views:
60,012
Posted By
Gerald D
For most people, the fact whether one is using...
For most people, the fact whether one is using SB, Mach or EMC, etc. should be "invisible". They are actually machine languages . . . . . most times only receiving a coded file and making the motors...
Showing results 1 to 13 of 13
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
05:12
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.