MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Showing results 1 to 9 of 9
Search took
0.00
seconds.
Search:
Posts Made By:
ger21
Forum:
MechMates already cutting
Sun 06 July 2014, 17:14
Replies:
414
Cutting Wing Rib Forms #118 - Oklahoma USA
Views:
223,656
Posted By
ger21
There are very few tools under $3000 that are as...
There are very few tools under $3000 that are as good as they were 15 years ago.
Unfortunately, paying double HF's price is still a very cheap tool, and with tools, you get what you pay for. ...
Forum:
MechMates already cutting
Wed 28 May 2014, 06:29
Replies:
414
Cutting Wing Rib Forms #118 - Oklahoma USA
Views:
223,656
Posted By
ger21
He didn't mean to plunge a V-bit into the center....
He didn't mean to plunge a V-bit into the center. You just go around the circle to the depth of the bevel, either before or after you cut the center out.
Forum:
MechMates already cutting
Mon 26 May 2014, 21:01
Replies:
414
Cutting Wing Rib Forms #118 - Oklahoma USA
Views:
223,656
Posted By
ger21
Is there some backlash in your Z axis? The Z axis...
Is there some backlash in your Z axis? The Z axis was not going down to the correct depth, or it would have cut through.
Forum:
MechMates already cutting
Mon 26 May 2014, 20:05
Replies:
414
Cutting Wing Rib Forms #118 - Oklahoma USA
Views:
223,656
Posted By
ger21
Sorry, I didn't read the first post, as it was on...
Sorry, I didn't read the first post, as it was on the previous page.
For very thin material like that, a downcut bit will be better. An upcut will bend the edges up at the cut.
How deep into...
Forum:
MechMates already cutting
Mon 26 May 2014, 19:42
Replies:
414
Cutting Wing Rib Forms #118 - Oklahoma USA
Views:
223,656
Posted By
ger21
http://www.amanatool.com/cncroutingdetails/aluminu...
http://www.amanatool.com/cncroutingdetails/aluminum-cnc-spiral-bit-51402.html
A downcut will work on thin aluminum, IF you cut it in one pass. If cutting less than full depth, there's no place for...
Forum:
MechMates already cutting
Mon 26 May 2014, 19:18
Replies:
414
Cutting Wing Rib Forms #118 - Oklahoma USA
Views:
223,656
Posted By
ger21
Do NOT use downcut bits to cut aluminum. They...
Do NOT use downcut bits to cut aluminum. They don't work very well, and won;t last long.
Get a single flute "O" flute bit.
Forum:
MechMates already cutting
Wed 23 April 2014, 09:41
Replies:
414
Cutting Wing Rib Forms #118 - Oklahoma USA
Views:
223,656
Posted By
ger21
If you search at CNC Zone, someone wrote a small...
If you search at CNC Zone, someone wrote a small program to output g-code for spirograph type designs. It's posted there somewhere, but it was over 5 years ago.
Forum:
MechMates already cutting
Sun 20 April 2014, 11:18
Replies:
414
Cutting Wing Rib Forms #118 - Oklahoma USA
Views:
223,656
Posted By
ger21
Someone at CNC Zone just did a test with a 300GPH...
Someone at CNC Zone just did a test with a 300GPH pump.
He measured the time it took for 1 gallon of water to flow through the spindle. It took 2 minutes, 54 seconds, or about 20.6GPH.
...
Forum:
MechMates already cutting
Sun 30 March 2014, 05:49
Replies:
414
Cutting Wing Rib Forms #118 - Oklahoma USA
Views:
223,656
Posted By
ger21
On the industrial machines I've used, the cables...
On the industrial machines I've used, the cables are tied where they enter and exit the chain, not within the chain itself. Typically the end pieces of the chain have provisions for tying the cable...
Showing results 1 to 9 of 9
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
15:54
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.